參數資料
型號： TPA3107D2_07
廠商： Texas Instruments, Inc.
英文描述： 15-W STEREO CLASS-D AUDIO POWER AMPLIFIER
中文描述： 15 W立體聲D類音頻功率放大器
文件頁數： 19/36頁
文件大?。?/td> 510K
代理商： TPA3107D2_07
www.ti.com
Bootstrap Capacitors
VCLAMP Capacitors
Internal Regulated 4-V Supply (VREG)
VBYP Capacitor Selection
ROSC Resistor Selection
F
=
OSC
1
2 x ROSC x COSC
(4)
TPA3107D2
SLOS509A–OCTOBER 2006–REVISED NOVEMBER 2006
The full H-bridge output stages use only NMOS transistors. Therefore, they require bootstrap capacitors for the
high side of each output to turn on correctly. A 220-nF ceramic capacitor, rated for at least 25 V, must be
connected from each output to its corresponding bootstrap input. Specifically, one 220-nF capacitor must be
connected from xOUTP to BSxx, and one 220-nF capacitor must be connected from xOUTN to BSxx. (See the
application circuit diagram in
Figure 19
.)
The bootstrap capacitors connected between the BSxx pins and corresponding output function as a floating
power supply for the high-side N-channel power MOSFET gate drive circuitry. During each high-side switching
cycle, the bootstrap capacitors hold the gate-to-source voltage high enough to keep the high-side MOSFETs
turned on.
To ensure that the maximum gate-to-source voltage for the NMOS output transistors is not exceeded, two
internal regulators clamp the gate voltage. Two 1-
μ
F capacitors must be connected from VCLAMPL (pin 40) and
VCLAMPR (pin 41) to ground and must be rated for at least 16 V. The voltages at the VCLAMPx terminals may
vary with V
CC
and may not be used for powering any other circuitry.
The VREG terminal (pin 19) is the output of an internally generated 4-V supply, used for the oscillator,
preamplifier, and gain control circuitry. It requires a 10-nF capacitor, placed close to the pin, to keep the
regulator stable.
This regulated voltage can be used to control GAIN0, GAIN1, MSTR/SLV, and MUTE terminals, but should not
be used to drive external circuitry.
The internal bias generator (VBYP) nominally provides a 1.25-V internal bias for the preamplifier stages. The
external input capacitors and this internal reference allow the inputs to be biased within the optimal
common-mode range of the input preamplifiers.
The selection of the capacitor value on the VBYP terminal is critical for achieving the best device performance.
During power up or recovery from the shutdown state, the VBYP capacitor determines the rate at which the
amplifier starts up. When the voltage on the VBYP capacitor equals VBYP, the device starts a 16.4-ms timer.
When this timer completes, the outputs start switching. The charge rate of the capacitor is calculated using the
standard charging formula for a capacitor, I = C x dV/dT. The charge current is nominally equal to 250μA and dV
is equal to VBYP. For example, a 1-μF capacitor on VBYP would take 5 ms to reach the value of VBYP and
begin a 16.4-ms count before the outputs turn on. This equates to a turn-on time of <30 ms for a 1-μF capacitor
on the VBYP terminal.
A secondary function of the VBYP capacitor is to filter high-frequency noise on the internal 1.25-V bias
generator. A value of at least 0.47μF is recommended for the VBYP capacitor. For the best power-up and
shutdown pop performance, the VBYP capacitor should be greater than or equal to the input capacitors.
The resistor connected to the ROSC terminal controls the class-D output switching frequency using
Equation 4
:
COSC is an internal capacitor that is nominally equal to 20 pF. Variation over process and temperature can
result in a
±
15% change in this capacitor value.
For example, if ROSC is fixed at 100 k
, the frequency from device to device with this fixed resistance could
vary from 217 kHz to 294 kHz with a 15% variation in the internal COSC capacitor. The tolerance of the ROSC
resistor should also be considered to determine the range of expected switching frequencies from device to
device. It is recommended that 1% tolerance resistors be used.
19
Submit Documentation Feedback
相關PDF資料
PDF描述
TPA3120D2_07 25-W STEREO CLASS-D AUDIO POWER AMPLIFIER
TPA5050_07 STEREO DIGITAL AUDIO LIP-SYNC DELAY WITH I2C CONTROL
TPA6204A1DGN R-78Bxx-1.0(L) Series - Innoline Regulated DC-DC Converters; Output Voltage (Vdc): 5.0V; Output Current (A): 1.0A; Features: Efficiency up to 97%,Non isolated, no need for heatsinks; Pin-out compatible with LM78XX Linears; Low profile( L*W*H=11.5*8.5*17.5mm); Wide input range.(4.75V ~ 34V); Short circuit protection, Thermal shutdown; Non standard outputs available as specialsbetween 1.5V ~15V; Low ripple and noise; ?L? version with 90?? pins
TPS2045P CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES
TPS2055P CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES
相關代理商/技術參數
參數描述
TPA3107D2EVM 功能描述:音頻 IC 開發工具 AUD POWER AMP RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
TPA3107D2PAP 功能描述:音頻放大器 15W Stereo Class-D Aud Power Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA3107D2PAPG4 功能描述:音頻放大器 15W Stereo Class-D Aud Power Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA3107D2PAPR 功能描述:音頻放大器 15W Stereo Class-D Audio Power Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA3107D2PAPRG4 功能描述:音頻放大器 15W Stereo Class-D Audio Power Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*