參數資料
型號: TP3054
廠商: National Semiconductor Corporation
元件分類: Codec
英文描述: “Enhanced” Serial Interface CMOS CODEC/Filter(加強型串行接口CMOS編解碼器/濾波器)
中文描述: “增強”串行接口的CMOS編解碼器/過濾器(加強型串行接口的CMOS編解碼器/濾波器)
文件頁數: 12/16頁
文件大?。?/td> 250K
代理商: TP3054
Applications Information
POWER SUPPLIES
While the pins of the TP305X family are well protected
against electrical misuse, it is recommended that the stan-
dard CMOS practice be followed, ensuring that ground is
connected to the device before any other connections are
made. In applications where the printed circuit board may be
plugged into a ‘‘hot’’ socket with power and clocks already
present, an extra long ground pin in the connector should
be used.
All ground connections to each device should meet at a
common point as close as possible to the GNDA pin. This
minimizes the interaction of ground return currents flowing
through a common bus impedance. 0.1
m
F supply decou-
pling capacitors should be connected from this common
ground point to V
CC
and V
BB
, as close to the device as
possible.
For best performance, the ground point of each CODEC/
FILTER on a card should be connected to a common card
ground in star formation, rather than via a ground bus.
This common ground point should be decoupled to V
CC
and
V
BB
with 10
m
F capacitors.
RECEIVE GAIN ADJUSTMENT
For applications where a TP305X family CODEC/filter re-
ceive output must drive a 600
X
load, but a peak swing lower
than
g
2.5V is required, the receive gain can be easily ad-
justed by inserting a matched T-pad or
q
-pad at the output.
Table II lists the required resistor values for 600
X
termina-
tions. As these are generally non-standard values, the equa-
tions can be used to compute the attenuation of the closest
practical set of resistors. It may be necessary to use un-
equal values for the R1 or R4 arms of the attenuators to
achieve a precise attenuation. Generally it is tolerable to
allow a small deviation of the input impedance from nominal
while still maintaining a good return loss. For example a 30
dB return loss against 600
X
is obtained if the output imped-
ance of the attenuator is in the range 282
X
to 319
X
(as-
suming a perfect transformer).
T-Pad Attenuator
R1
e
Z1
#
Where: N
e
0
N
2
a
1
N
2
b
1
J
b
2
0
Z1.Z2
#
N
N
2
b
1
J
R2
e
2
0
Z1.Z2
#
N
N
2
b
1
J
POWER IN
POWER OUT
and
S
e
0
Also: Z
e
0
Z
SC
#
Z
OC
Where Z
SC
e
impedance with short circuit termination
and Z
OC
e
impedance with open circuit termination
Z1
Z2
q
-Pad Attenuator
TL/H/5510–5
R3
e
0
Z1.Z2
2
#
N
2
b
1
N
J
R3
e
Z1
#
N
2
b
1
N
2
b
2NS
a
1
J
Note:
See Application Note 370 for further details.
12
相關PDF資料
PDF描述
TP3056BDWR PCM CODEC|SINGLE|CMOS|SOP|16PIN|PLASTIC
TP3056B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER
TP3056BDW MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER
TP3056BN MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER
TP3098 TRANSISTOR | BJT | NPN | 200MA I(C) | RFMOD
相關代理商/技術參數
參數描述
TP3054A 制造商:TI 制造商全稱:Texas Instruments 功能描述:MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER
TP3054ADW 功能描述:接口—CODEC PCM CODEC RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
TP3054ADWR 功能描述:接口—CODEC Mono Serial Intfc PCM Codec/Filter RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
TP3054AJ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:u-Law CODEC
TP3054AN 功能描述:接口—CODEC PCM CODEC RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel