- 您現在的位置：買賣IC網 > PDF目錄384017 > TMDS3788844 (Texas Instruments, Inc.) 3M710 INSERTION CUT TOOL PDF資料下載
參數資料
| 型號： | TMDS3788844 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 3M710 INSERTION CUT TOOL |
| 中文描述： | TMS370微控制器系列數據手冊 |
| 文件頁數： | 64/78頁 |
| 文件大?。?/td> | 919K |
| 代理商： | TMDS3788844 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁當前第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁
CUSTOMER-RETURNED-ITEMHANDLING PROCEDURE
3–10
POST OFFICE BOX 1443
HOUSTON, TEXAS 77251–1443
specific handling procedures for static-sensitive items (continued)
All such items must be shipped with an ESD warning label affixed as shown under the General Handling
Procedures and Requirements (for ESD sensitive devices and assemblies).
It is the responsibility of the area supervisor to ensure that all personnel handling static-sensitive items are
familiar with this procedure and fully aware of the damage or possible degradation of these units in the event
of noncompliance. A periodic inspection must be made using an electrostatic voltmeter to ensure that the
static-free workstations are in proper working order and to ensure that operators are wearing grounding
straps properly (snugly and in contact with bare skin).
packing operations
Static-sensitive items are not to be accepted into the packing area unless they are contained in a
static-protected bag or conductive container.
A static-sensitive item delivered to the packer within an approved container or bag and found to be in order
regarding identification must be packed in the standard shipping carton or other regular packaging material.
Containers are to be labeled in accordance with General Handling Procedures and Requirements.
Any void-fillers must be made of an approved antistatic material.
burn-in operations
Burn-in board loading and unloading of static-sensitive items must be done at a static-free workstation.
Shorting clips/shorted connectors must be installed on the board plug-in tab prior to loading any units into
the board sockets. The clip/connectors must be taken off just prior to plugging the board into the oven
connector. The clip/connector must be installed immediately upon removal of the board from the oven
connector. Installation and removal of the clip/connector must be done by a properly grounded operator.
All automatic or semi-automatic loading and unloading equipment must be properly electrically grounded.
It is the responsibility of the area supervisor to ensure that all personnel handling static-senstive items are
familiar with this procedure and fully aware of the damage or possible degradation of these units in the event
of noncompliance. A periodic inspection must be made using an electrostatic voltmeter to ensure that the
static-free workstations are in proper working order and to ensure that operators are wearing grounding
straps properly (snugly and in contact with bare skin).
customer-returned-item handling procedure
Receipt of ESD sensitive-labeled items is to be done at a static-free workstation and handled in accordance with
applicable sections within this guideline.
quality control provision
sampling
Each manufacturing, stockroom, and testing operation handling ESD sensitive devices is audited a minimum
of once each quarter for compliance with all terms of this specification by the responsible process control or QRA
organization. Ground continuity and the presence of uncontrolled static voltages are considered critical and
must be checked more frequently as specified below.
ground continuity (minimum of once a week)
Ground connections (grounding wrist strap, ground wires on cords, etc.) must be checked for electrical
continuity. The presence of a 1 M
±
10% resistor in the ground connections between both the operator wrist
straps to the work surface and the work surface to ground connector must be verified.
相關PDF資料 |
PDF描述 |
|---|---|
| TMDS3788868 | TMS370 MICROCONTROLLER FAMILY DATA BOOK |
| TMG5C80C | Through Hole/Non-isolated |
| TMOD0110G | 10 Gbits/s Modulator Driver(10 G位/秒調制驅動器) |
| TMOV20R575E | Varistor Products - Thermally Protected |
| TMOV20R200E | Varistor Products - Thermally Protected |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMDS3788868 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:TMS370 MICROCONTROLLER FAMILY DATA BOOK |
| TMDS3P603070 | 功能描述:EVALUTION MODULE RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:* |
| TMDS3P701016 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| TMDS3P701016A | 功能描述:開發板和工具包 - TMS320 TMDS3P701016A Eval Mod RoHS:否 制造商:Texas Instruments 產品:Experimenter Kits 工具用于評估:F2802x 核心:TMS320 接口類型:UART, USB 工作電源電壓: |
| TMDS3P701016AE | 功能描述:EVAL MODULE FOR LF2407A RoHS:否 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:- 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。