- 您現在的位置：買賣IC網 > PDF目錄98266 > TMDS261PAGR (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PQFP64 PDF資料下載
參數資料
| 型號： | TMDS261PAGR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| 封裝： | GREEN, PLASTIC, TQFP-64 |
| 文件頁數： | 12/43頁 |
| 文件大小： | 2160K |
| 代理商： | TMDS261PAGR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
DESCRIPTION (CONTINUED)
SLLS953 – DECEMBER 2008............................................................................................................................................................................................ www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
When any of the input ports are selected, the integrated terminations (50-
termination resistors pulled up to
VCC) are switched on for the TMDS clock channel, the TMDS clock-detection circuit is enabled, and the DDC
repeater is enabled. After a valid TMDS clock is detected, the integrated termination resistors for the data lines
are enabled, and the output TMDS lines are enabled. When an input port is not selected, the integrated
terminations are switched off, the TMDS receivers are disabled, and the DDC repeater is disabled.
Clock-detection circuitry provides an automatic power-management feature, because if no valid TMDS clock is
detected, the terminations on the input TMDS data lines are disconnected and the TMDS outputs are placed in a
high-impedance state.
The TMDS261 is designed to be controlled via a local I2C interface or GPIO interface based on the status of the
I2C_SEL pin. The local I2C interface in TMDS261 is a slave-only I2C interface. (See the I2C INTERFACE
NOTES section.)
I2C Mode: When the I2C_SEL pin is set low, the device is in I2C mode. With local I2C, the interface port status
can be read and the advanced configurations of the device such as TMDS output edge rate control, DDC I2C
buffer output-voltage-select (OVS) settings (See the DDC I2C Function Description for detailed description on
DDC I2C buffer description and OVS description), device power management, TMDS clock-detect feature and
GPIO mode: When the I2C_SEL pin is set high, the device is in GPIO control mode. The port selection is
controlled with source selectors, S1 and S2. The power-saving mode is controlled through the LP pin. In GPIO
mode, the default TMDS output edge rate that is the fastest setting of rise and fall time is set, and the default
DDC I2C buffer OVS setting (OVS3) is set. See Table 8 and the DDC I2C Function Description for detailed
description of the DDC I2C buffer.
Following are some of the key features (advantages) that TMDS261 provides to the overall sink-side system
(HDTV).
2×1 switch that supports TMDS data rates up to 3 Gbps on all two input ports.
ESD: Built-in support for high ESD protection (up to 10 kV on the HDMI source side). The HDMI source-side
pins on the TMDS261 are connected via the HDMI/DVI exterior connectors and cable to the HDMI/DVI
sources (e.g., DVD player). In TV applications, it can be expected that the source side may be subjected to
higher ESD stresses compared to the sink side that is connected internally to the HDMI receiver.
Adaptive equalization: The built-in adaptive equalization support compensates for intersymbol interference
[ISI] loss of up to 20 dB, which represents a typical 20-m HDMI/DVI cable at 3 Gbps. Adaptive equalization
adjusts the equalization gain automatically, based on the cable length and the incoming TMDS data rate.
TMDS clock-detect circuitry: This feature provides an automatic power-management feature and also ensures
that the TMDS output port is turned on only if there is a valid TMDS input signal. TMDS clock-detect feature
can be by-passed in I2C Mode, See Table 10 and Table 11. It is recommended to enable TMDS clock-detect
circuitry during normal operation. However, for HDMI compliance testing (TMDS Termination Voltage Test),
the clock detect feature should be disabled by using the I2C Mode control. If the customer requires to pass
TMDS Termination Voltage Test in GPIO mode with default TMDS clock-detect circuitry enabled, then a valid
TMDS clock should be provided for this complaince test, so that the terminations on the TMDS data pair can
be connected and thus customer can pass the TMDS Termination Voltage Test.
DDC I2C buffer: This feature provides isolation on the source side and sink side DDC I2C capacitance, thus
helping the sink system to pass system-level compliance.
Robust TMDS receive stage: This feature ensures that the TMDS261 can work with TMDS input signals
having common-mode voltage levels that can be either compliant or non-compliant with HDMI/DVI
specifications.
VSadj: This feature adjusts the TMDS output swing and can help the sink system to tune the output TMDS
swing of the TMDS261 (if needed) based on the system requirements.
GPIO or local I2C interface to control the device features
TMDS output edge-rate control: This feature adjusts the TMDS261 TMDS output rise and fall times. There
are four settings of the rise and fall times that can be chosen. The default setting is the fastest rise and fall
2
Copyright 2008, Texas Instruments Incorporated
Product Folder Link(s) :TMDS261
相關PDF資料 |
PDF描述 |
|---|---|
| TMDS261PAG | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TMDS341APFCR | 3-CHANNEL, AUDIO/VIDEO SWITCH, PQFP80 |
| TMDS351PAGR | 3-CHANNEL, AUDIO/VIDEO SWITCH, PQFP64 |
| TMDS361PAGR | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TMDS361PAG | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMDS28027USB | 功能描述:仿真器/模擬器 TMX320F28027 Piccolo controlSTICK RoHS:否 制造商:Blackhawk 產品:System Trace Emulators 工具用于評估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2 |
| TMDS2MTRPFCKIT | 功能描述:電源管理IC開發工具 Dual Motor Control and PFC Dev Kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TMDS3080005 | 功能描述:EMULATOR CABLE RoHS:是 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF) |
| TMDS3200026 | 制造商:Texas Instruments 功能描述:KIT-DSP STARTER PACK |
| TMDS3200031 | 制造商:Texas Instruments 功能描述:STARTER KIT C3X |
發布緊急采購，3分鐘左右您將得到回復。