- 您現在的位置：買賣IC網 > PDF目錄385930 > TLED2043 (Texas Instruments, Inc.) 4-CHANNEL WHITE LED DRIVER(四通道白色LED驅動器) PDF資料下載
參數資料
| 型號： | TLED2043 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 4-CHANNEL WHITE LED DRIVER(四通道白色LED驅動器) |
| 中文描述： | 4通道白光LED驅動器（四通道白色發光二極管驅動器） |
| 文件頁數： | 10/15頁 |
| 文件大小： | 221K |
| 代理商： | TLED2043 |
TLED2043
4-CHANNEL WHITE LED DRIVER
SLDS147C
–
JUNE 2002
–
REVISED NOVEMBER 2002
10
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
DEVICE OPERATION/APPLICATION HINTS
Refer to the functional block diagram and typical application circuit (see Figure 8)
White LEDs commonly are used to produce the backlight for small color LCDs found in portable electronics,
such as cell phones and PDAs. Because the LED
’
s brightness and chromaticity are dependent on the LED
’
s
bias current, precise control of this current is necessary for proper illumination of the LCD. The TLED2043 is,
essentially, four voltage-controlled current sinks that are regulated in unison, with each current sink setting the
bias current for one white LED. The basic circuitry and operation of the TLED2043 can be divided into three main
operating blocks described below.
output FETs
The TLED2043 has four n-channel MOSFETs to drive four external LEDs. The FETs have a specified maximum
r
on
of 6
, while delivering 20 mA of load current. To determine the biasing current for each LED, the gate of
each FET is driven by a buffer whose output is controlled by the current-control amplifier.
current control amplifier
The output of the Current Control Amplifier simultaneously drives four unity-gain amplifiers connected to the
gates of the output FETs. To determine the drain current of each FET (the LED current), the noninverting input
(IN+) of this amplifier typically is coupled to the battery voltage via Switch 1, while the inverting input (IN
–
)
typically is coupled to a fixed reference voltage that remains constant as battery voltage changes. Therefore,
the output of the Current Control Amplifier and the corresponding LED currents are proportional to the difference
between the battery and reference voltages. As battery voltage drops with use, so does the LED current,
allowing for lower power consumption to conserve battery power.
switch 1, 2, 3
The TLED2042 has three switches that are opened/closed in unison via an active-low switch-enable (SW)
pin;
the switches are closed with a low input applied and opened with a high input. Each switch has a maximum loss
of 0.1 V across it; thus, the output of each switch is specified to be (V
IN
–
0.1 V) < V
OUT
< V
IN
.
During periods of inactivity when the LEDs are not needed, significant power savings can be achieved (from
a maximum of 1 mA to 1
μ
A) by opening the switches. The purpose of each switch is described below:
Switch 1: used to remove power to the TLED2043 when the LEDs are not needed.
Switch 2 (or 3): used to remove power to the series voltage reference (V
REF
in the typical application
Circuit). Without this switch, V
REF
current flows continuously (through R1 and R2), even when power is
removed from the TLED2043. (Note that, if a shunt reference like the TLV431 is used, current still flows
through the reference, even if Switch 2 is open).
Switch 3: Though not used in the typical application circuit here, this switch can be used to connect
various external circuitries to the current-control amplifier. One example is to connect an external
voltage to either input of the current-control amplifier to implement an analog LED brightness control
(see next section).
相關PDF資料 |
PDF描述 |
|---|---|
| TLFGE18TP | Toshiba TLxE18 Series LEDs |
| TLPYE18TP | Toshiba TLxE18 Series LEDs |
| TLGA158P | Low Drive Current,High Intensity Green Light Emission(LED Lamp )(小驅動電流，高亮度綠光燈（LED照明燈）) |
| TLGA159P | Low Drive Current,High Intensity Green Light Emission(LED Lamp )(小驅動電流，高亮度綠光燈（LED照明燈）) |
| TLGD135AP | Low Drive Current,High Intensity Green Light Emission(LED Lamp )(小驅動電流，高亮度綠光燈（LED照明燈）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLED2043IGQNR | 功能描述:IC LED DRIVER LINEAR 20-VFBGA RoHS:否 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:1 系列:- 恒定電流:- 恒定電壓:- 拓撲:PWM，切換式電容器（充電泵） 輸出數:1 內部驅動器:是 類型 - 主要:背光 類型 - 次要:白色 LED 頻率:642kHz 電源電壓:2.7 V ~ 5.5 V 輸出電壓:5V 安裝類型:表面貼裝 封裝/外殼:10-VFDFN 裸露焊盤 供應商設備封裝:10-VSON 包裝:剪切帶 (CT) 工作溫度:-30°C ~ 85°C 產品目錄頁面:1371 (CN2011-ZH PDF) 其它名稱:BD1603NUV-E2CT |
| TLED2043IPWR | 功能描述:LED照明驅動器 4ch White LED RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| TLED25W-036-C0700-D | 功能描述:LED DRIVER CC AC/DC 12-36V 700MA 制造商:thomas research products 系列:TLED-25W 零件狀態:在售 類型:恒定電流 拓撲:AC DC 轉換器 輸出數:1 電壓 - 輸入（最小值）:108VAC 電壓 - 輸入（最大值）:305VAC 電壓 - 輸出:12 ~ 36 V 電流 - 輸出（最大值）:700mA 功率（W）:25W 調光:模擬 特性:OCP，OVP，SCP 等級:IP66 工作溫度:- 效率:83% 端子類型:導線引線 大小/尺寸:3.78" 長 x 2.44" 寬 x 1.18" 高（96.0mm x 62.0mm x 30.0mm） 安裝類型:底座安裝 認可:CE，cURus 重量:- 標準包裝:500 |
| TLED40W-054-C0700-D | 功能描述:LED DRIVER CC AC/DC 30-54V 700MA 制造商:thomas research products 系列:TLED-40W 零件狀態:在售 類型:恒定電流 拓撲:AC DC 轉換器 輸出數:1 電壓 - 輸入（最小值）:108VAC 電壓 - 輸入（最大值）:305VAC 電壓 - 輸出:30 ~ 54 V 電流 - 輸出（最大值）:700mA 功率（W）:40W 調光:模擬 特性:OCP，OVP，SCP 等級:IP66，NEMA 4 工作溫度:- 效率:86% 端子類型:導線引線 大小/尺寸:3.78" 長 x 2.80" 寬 x 1.26" 高（96.0mm x 71.0mm x 32.0mm） 安裝類型:底座安裝 認可:cURus 重量:- 標準包裝:500 |
| TLEGC1002 | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Panel Circuit Indicator |
發布緊急采購，3分鐘左右您將得到回復。