- 您現在的位置：買賣IC網 > PDF目錄385930 > TLC7135C (Texas Instruments, Inc.) Analog-to-Digital Converters(并行接口4 1/2位A/D轉換器) PDF資料下載
參數資料
| 型號： | TLC7135C |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | Analog-to-Digital Converters(并行接口4 1/2位A/D轉換器) |
| 中文描述： | 模擬到數字轉換器（并行接口4 1 / 2位的A / D轉換器） |
| 文件頁數： | 9/11頁 |
| 文件大小： | 224K |
| 代理商： | TLC7135C |
ICL7135C, TLC7135C
4 1/2-DIGIT PRECISION
ANALOG-TO-DIGITAL CONVERTERS
SLAS074A – DECEMBER 1986 – REVISED MAY 1995
2–11
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
integrating capacitor
The product of the integrating resistor and capacitor should be selected to give the maximum voltage swing
without causing the integrating amplifier output to saturate and get too close to the power supply voltages. When
the amplifier output is within 0.3 V of either supply, saturation occurs. With
±
5-V supplies and ANLG COMMON
connected to ground, the designer should design for a
±
3.5-V to
±
4-V integrating amplifier swing. A nominal
capacitor value is 0.47
μ
F. The equation for determining the value of the integrating capacitor (C
INT
) is:
CINT
10,000
Integrator Output Voltage Swing
Clock Period
IINT
Where:
I
INT
is nominally 20
μ
A.
Capacitors with large tolerances and high dielectric absorption can induce conversion inaccuracies. A capacitor
that is too small could cause the integrating amplifier to saturate. High dielectric absorption causes the effective
capacitor value to be different during the signal integrate and deintegrate phases. Polypropylene capacitors
have very low dielectric absorption. Polystyrene and polycarbonate capacitors have higher dielectric
absorption, but also work well.
auto-zero and reference capacitor
Large capacitors tend to reduce noise in the system. Dielectric absorption is unimportant except during power
up or overload recovery. Typical values are 1
μ
F.
reference voltage
For high-accuracy absolute measurements, a high quality reference should be used.
rollover resistor and diode
The ICL7135C and TLC7135C have a small rollover error; however, it can be corrected. The correction is to
connect the cathode of any silicon diode to INT OUT and the anode to a resistor. The other end of the resistor
is connected to ANLG COMMON or ground. For the recommended operating conditions, the resistor value is
100 k
. This value may be changed to correct any rollover error that has not been corrected. In many noncritical
applications the resistor and diode are not needed.
maximum clock frequency
For most dual-slope A/D converters, the maximum conversion rate is limited by the frequency response of the
comparator. In this circuit, the comparator follows the integrator ramp with a 3-
μ
s delay. Therefore, with a
160-kHz clock frequency (6-
μ
s period), half of the first reference integrate clock period is lost in delay. Hence,
the meter reading changes from 0 to 1 with a 50-
μ
V input, 1 to 2 with a 150-
μ
V input, 2 to 3 with a 250-
μ
V input,
etc. This transition at midpoint is desirable; however, when the clock frequency is increased appreciably above
160 kHz, the instrument flashes 1 on noise peaks even when the input is shorted. The above transition points
assume a 2-V input range is equivalent to 20,000 clock cycles.
When the input signal is always of one polarity, comparator delay need not be a limitation. Clock rates of 1 MHz
are possible since nonlinearity and noise do not increase substantially with frequency. For a fixed clock
frequency, the extra count or counts caused by comparator delay are a constant and can be subtracted out
digitally.
相關PDF資料 |
PDF描述 |
|---|---|
| TLC7225(中文) | Quadruple 8-Bit Digital-To-Analog Converters(四通道，電壓輸出，8位DAC) |
| TLC7226(中文) | Quadruple 8-Bit Digital-To-Analog Converters(四路8位D/A轉換器) |
| TLC7524(中文) | 8-Bit Multipling DAC(單路8位乘法DAC) |
| TLC7528(中文) | Dual 8-Bit Multipling DAC(雙通道8位乘法DAC) |
| TLC7528EFN | DUAL 8-BIT MULTIPLYING DIGITAL-TO-ANALOG CONVERTERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLC7135CDW | 功能描述:LED顯示驅動器 Dual Slope A/D RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| TLC7135CDWG4 | 功能描述:LED顯示驅動器 4.5-Bits 0.003 kSPS Muxed BCD Out RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| TLC7135CDWR | 功能描述:LED顯示驅動器 4.5-Bits 0.003 kSPS Muxed BCD Out RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| TLC7135CDWRG4 | 功能描述:LED顯示驅動器 4.5-Bits 0.003 kSPS Muxed BCD Out RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| TLC7135CN | 功能描述:LED顯示驅動器 4.5digit .003ksps RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。