- 您現在的位置：買賣IC網 > PDF目錄383949 > TL16C550CIPFB (Texas Instruments, Inc.) ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH AUTOFLOW CONTROL PDF資料下載
參數資料
| 型號： | TL16C550CIPFB |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH AUTOFLOW CONTROL |
| 中文描述： | 異步通信與自動流速調節(jié)控制單元 |
| 文件頁數： | 27/35頁 |
| 文件大小： | 499K |
| 代理商： | TL16C550CIPFB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
TL16C550B, TL16C550BI
ASYNCHRONOUS COMMUNICATIONS ELEMENT
SLLS136B – JANUARY 1994 – REVISED AUGUST 1996
27
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
line status register (LSR) (continued)
Bit 2
: This bit is the parity error (PE) indicator. When bit 2 is set, it indicates that the parity of the received
data character does not match the parity selected in the LCR (bit 4). The PE bit is cleared every time the
CPU reads the contents of the LSR. In the FIFO mode, this error is associated with the particular character
in the FIFO to which it applies. This error is revealed to the CPU when its associated character is at the top
of the FIFO.
Bit 3
: This bit is the framing error (FE) indicator. When bit 3 is set, it indicates that the received character
did not have a valid (set) stop bit. The FE bit is cleared every time the CPU reads the contents of the LSR.
In the FIFO mode, this error is associated with the particular character in the FIFO to which it applies. This
error is revealed to the CPU when its associated character is at the top of the FIFO. The ACE tries to
resynchronize after a framing error. To accomplish this, it is assumed that the framing error is due to the
next start bit. The ACE samples this start bit twice and then accepts the input data.
Bit 4
: This bit is the break interrupt (BI) indicator. When bit 4 is set, it indicates that the received data input
was held cleared for longer than a full-word transmission time. A full-word transmission time is defined as
the total time of the start, data, parity, and stop bits. The BI bit is cleared every time the CPU reads the
contents of the LSR. In the FIFO mode, this error is associated with the particular character in the FIFO to
which it applies. This error is revealed to the CPU when its associated character is at the top of the FIFO.
When a break occurs, only one 0 character is loaded into the FIFO. The next character transfer is enabled
after SIN goes to the marking state and receives the next valid start bit.
Bit 5: This bit is the THRE indicator. Bit 5 is set when the THR is empty, indicating that the ACE is ready
to accept a new character. If the THRE interrupt is enabled when the THRE bit is set, an interrupt is
generated. THRE is set when the contents of the THR are transferred to the transmitted shift register. This
bit is cleared concurrent with the loading of the THR by the CPU. In the FIFO mode, this bit is set when the
transmit FIFO is empty; it is cleared when at least one byte is written to the transmit FIFO.
Bit 6: This bit is the transmitter empty (TEMT) indicator. Bit 6 is set when the THR and the TSR are both
empty. When either the THR or the TSR contains a data character, the TEMT bit is cleared. In the FIFO
mode, this bit is set when the transmitter FIFO and shift register are both empty.
Bit 7: In the TL16C550B and the TL16C550BI mode, this bit is always cleared. In the TL16C450 mode, this
bit is always cleared. In the FIFO mode, LSR7 is set when there is at least one parity, framing, or break error
in the FIFO. It is cleared when the microprocessor reads the LSR and there are no subsequent errors in
the FIFO.
modem control register (MCR)
The MCR is an 8-bit register that controls an interface with a modem, data set, or peripheral device that is
emulating a modem. The contents of this register are summarized in Table 3 and are described in the following
bulleted list.
Bit 0: This bit (DTR) controls the data terminal ready (DTR) output. Setting bit 0 forces the DTR output to
its low state. When bit 0 is cleared, DTR goes high.
Bit 1: This bit (RTS) controls the request to send (RTS) output in a manner identical to bit 0’s control over
the DTR output.
Bit 2: This bit (OUT1) controls the output 1 (OUT1) signal, a user-designated output signal, in a manner
identical to bit 0’s control over the DTR output.
The line status register is intended for read operations only; writing to this register is not recommended outside of a factory testing environment.
Bits 1 through 4 are the error conditions that produce a receiver line status interrupt.
相關PDF資料 |
PDF描述 |
|---|---|
| TL16C552AMPN | DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO |
| TL16C552AHV | DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO |
| TL16C552AMFN | DUAL ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH FIFO |
| TL16C554AI | ASYNCHRONOUS-COMMUNICATIONS ELEMENT |
| TL16C554I | ASYNCHRONOUS COMMUNICATIONS ELEMENT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TL16C550CIPT | 功能描述:UART 接口集成電路 Sngl UART w/16-Byte FIFOs & Aut Flw Ctrl RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| TL16C550CIPTG4 | 功能描述:UART 接口集成電路 Sngl UART w/16-Byte FIFOs & Aut Flw Ctrl RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| TL16C550CIPTR | 功能描述:UART 接口集成電路 Sngl UART w/16-Byte FIFOs & Aut Flw Ctrl RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| TL16C550CIPTRG4 | 功能描述:UART 接口集成電路 Sngl UART w/16-Byte FIFOs & Aut Flw Ctrl RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| TL16C550CN | 功能描述:UART 接口集成電路 Sngl UART w/16-Byte FIFOs & Aut Flw Ctrl RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。