參數資料
型號： TJA1054AU
廠商： NXP SEMICONDUCTORS
元件分類： 網絡接口
英文描述： Fault-tolerant CAN transceiver
中文描述： DATACOM, INTERFACE CIRCUIT, UUC15
封裝： DIE-15
文件頁數： 8/25頁
文件大小： 144K
代理商： TJA1054AU
2004 Mar 23
8
Philips Semiconductors
Product specification
Fault-tolerant CAN transceiver
TJA1054A
3.
4.
A local or remote wake-up event will be signalled at the transceiver pins RXD and NERR if V
BAT
= 5.3 V to 27 V.
In case the goto-sleep command was used before. When V
CC
drops, pin EN will become LOW, but due to the
fail-safe functionality this does not effect the internal functions.
V
BAT
power-on flag will be reset when entering normal operating mode.
5.
Wake-up requests are recognized by the transceiver
through two possible channels:
The bus lines for remote wake-up
Pin WAKE for local wake-up.
In order to wake-up the transceiver remotely through the
bus lines, a filter mechanism is integrated. This
mechanism makes sure that noise and any present bus
failure conditions do not result into an erroneous wake-up.
Because of this mechanism it is not sufficient to simply pull
the CANH or CANL bus lines to a dominant level for a
certain time. To guarantee a successful remote wake-up
under all conditions, a message frame with a dominant
phase of at least the maximum specified t
CANH
or t
CANL
in
it is required.
A local wake-up through pin WAKE is detected by a rising
or falling edge with a consecutive level with the maximum
specified t
WAKE
.
On a wake-up request the transceiver will set the output on
pin INHtoHIGHwhichcanbeusedtoactivatetheexternal
supply voltage regulator.
If V
CC
is provided the wake-up request can be read on the
ERR or RXD outputs, so the external microcontroller can
activate the transceiver (switch to normal operating mode)
via pins STB and EN.
To prevent a false remote wake-up due to transients or
RF fields, the wake-up voltage levels have to be
maintained for a certain period of time. In the low power
modes the failure detection circuit remains partly active to
prevent an increased power consumption in the event of
failures 3, 3a, 4 and 7.
To prevent a false local wake-up during an open wire at
pin WAKE, this pin has a weak pull-up current source
towards V
BAT
. However, in order to prevent EMC issues, it
is recommended to connect a not used pin WAKE to pin
BAT. Pin INH is set to floating only if the goto-sleep
command is entered successfully. To enter a successful
goto-sleep command under all conditions, this command
must be kept stable for the maximum specified t
h(sleep)
.
Pin INH will be set to a HIGH level again by the following
events only:
V
BAT
power-on (cold start)
Rising or falling edge on pin WAKE
A message frame with a dominant phase of at least the
maximum specified t
CANH
or t
CANL
, while pin EN or
pin STB is at a LOW level
Pin STB goes to a HIGH level with V
CC
active.
To provide fail-safe functionality, the signals on pins STB
and EN will internally be set to LOW when V
CC
is below a
certain threshold voltage (V
CC(stb)
).
Power-on
After power-on (V
BAT
switched on) the signal on pin INH
willbecomeHIGHandaninternalpower-onflagwillbeset.
This flag can be read in the power-on standby mode
through pin ERR (STB = 1; EN = 0) and will be reset by
entering the normal operating mode.
Protections
A current limiting circuit protects the transmitter output
stages against short-circuit to positive and negative
battery voltage.
If the junction temperature exceeds the typical value of
165
°
C, the transmitter output stages are disabled.
Because the transmitter is responsible for the major part of
the power dissipation, this will result in a reduced power
dissipation and hence a lower chip temperature. All other
parts of the device will continue to operate.
The pins CANH and CANL are protected against electrical
transients which may occur in an automotive environment.
相關PDF資料
PDF描述
TK11149ASIL 4.9 V FIXED POSITIVE LDO REGULATOR, 0.2 V DROPOUT, PDSO5
TK11148ASIL 4.8 V FIXED POSITIVE LDO REGULATOR, 0.2 V DROPOUT, PDSO5
TK11147ASIL 4.7 V FIXED POSITIVE LDO REGULATOR, 0.2 V DROPOUT, PDSO5
TK11146ASIL 4.6 V FIXED POSITIVE LDO REGULATOR, 0.2 V DROPOUT, PDSO5
TK11144ASIL 4.4 V FIXED POSITIVE LDO REGULATOR, 0.2 V DROPOUT, PDSO5
相關代理商/技術參數
參數描述
TJA1054T 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Fault-tolerant CAN transceiver
TJA1054T/N,112 功能描述:網絡控制器與處理器 IC FAULT TOLERANT TRANSCEIVER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
TJA1054T/N,118 功能描述:網絡控制器與處理器 IC FAULT TOLERANT TRANSCEIVER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
TJA1054T/N1 制造商:NXP Semiconductors 功能描述:DATACOM, INTERFACE CIRCUIT, PDSO14
TJA1054T/N1,512 功能描述:網絡控制器與處理器 IC CAN XCVR FAULT-TOL RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*