- 您現在的位置：買賣IC網 > PDF目錄359289 > TJA1054AU (NXP SEMICONDUCTORS) Fault-tolerant CAN transceiver PDF資料下載
參數資料
| 型號： | TJA1054AU |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 網絡接口 |
| 英文描述： | Fault-tolerant CAN transceiver |
| 中文描述： | DATACOM, INTERFACE CIRCUIT, UUC15 |
| 封裝： | DIE-15 |
| 文件頁數： | 7/25頁 |
| 文件大?。?/td> | 144K |
| 代理商： | TJA1054AU |
2004 Mar 23
7
Philips Semiconductors
Product specification
Fault-tolerant CAN transceiver
TJA1054A
Failure 6 is detected if the CANL bus line exceeds its
comparator threshold for a certain period of time. This
delay is needed to avoid false triggering by external RF
fields. After detection of failure 6, the reception is switched
to the single-wire mode through CANH; the CANL driver is
switched off and the RTL bias changes to the pull-up
current source.
Recovery from failures 3, 3a and 6 is detected
automatically after reading a consecutive recessive level
by corresponding comparators for a certain period of time.
Failures 4 and 7 initially result in a permanent dominant
level on pin RXD. After a time-out the CANL driver is
switched off and the RTL bias changes to the pull-up
current source. Reception continues by switching to the
single-wire mode via pins CANH or CANL. When
failures 4 or 7 are removed, the recessive bus levels are
restored. If the differential voltage remains below the
recessive threshold level for a certain period of time,
reception and transmission switch back to the differential
mode.
If any of the wiring failure occurs, the output signal on
pin ERR will be set to LOW. On error recovery, the output
signal on pin ERR will be set to HIGH again. In case of an
interrupted open bus wire, this failure will be detected and
signalled only if there is an open wire between the
transmitting and receiving node(s). Thus, during open wire
failures, pin ERR typically toggles.
During all single-wire transmissions, EMC performance
(both immunity and emission) is worse than in the
differential mode. The integrated receiver filters suppress
any HF noise induced into the bus wires. The cut-off
frequency of these filters is a compromise between
propagation delay and HF suppression. In single-wire
mode, LF noise cannot be distinguished from the required
signal.
Low power modes
The transceiver provides three low power modes which
can be entered and exited via STB and EN (see Table 2
and Fig.3).
The sleep mode is the mode with the lowest power
consumption. Pin INH is switched to HIGH-impedance for
deactivation of the external voltage regulator. Pin CANL is
biased to the battery voltage via pin RTL. If the supply
voltage is provided, pins RXD and ERR will signal the
wake-up interrupt.
The standby mode operates in the same way as the sleep
mode but with a HIGH level on pin INH.
The power-on standby mode is the same as the standby
mode, however, in this mode the battery power-on flag is
shown on pin ERR instead of the wake-up interrupt signal.
The output on pin RXD will show the wake-up interrupt.
This mode is only for reading out the power-on flag.
Table 2
Normal operating and low power modes
Notes
1.
2.
If the supply voltage V
CC
is present.
Wake-up interrupts are released when entering normal operating mode.
MODE
PIN
STB
PIN EN
PIN ERR
PIN RXD
PIN RTL
SWITCHED
TO
V
BAT
LOW
HIGH
LOW
HIGH
Goto-sleep
command
Sleep
Standby
Power-on
standby
LOW
HIGH
wake-up
interruptsignal;
notes 1 2 and 3
wake-up
interruptsignal;
notes 1 2 and 3
LOW
LOW
HIGH
LOW
(4)
LOW
LOW
V
BAT
power-on
flag;
notes 1 and 5
error flag
wake-up
interruptsignal;
notes 1 2 and 3
dominant
received data
V
BAT
Normal
operating
HIGH
HIGH
no error flag
recessive
received data
V
CC
相關PDF資料 |
PDF描述 |
|---|---|
| TK11149ASIL | 4.9 V FIXED POSITIVE LDO REGULATOR, 0.2 V DROPOUT, PDSO5 |
| TK11148ASIL | 4.8 V FIXED POSITIVE LDO REGULATOR, 0.2 V DROPOUT, PDSO5 |
| TK11147ASIL | 4.7 V FIXED POSITIVE LDO REGULATOR, 0.2 V DROPOUT, PDSO5 |
| TK11146ASIL | 4.6 V FIXED POSITIVE LDO REGULATOR, 0.2 V DROPOUT, PDSO5 |
| TK11144ASIL | 4.4 V FIXED POSITIVE LDO REGULATOR, 0.2 V DROPOUT, PDSO5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TJA1054T | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Fault-tolerant CAN transceiver |
| TJA1054T/N,112 | 功能描述:網絡控制器與處理器 IC FAULT TOLERANT TRANSCEIVER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發(fā)器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| TJA1054T/N,118 | 功能描述:網絡控制器與處理器 IC FAULT TOLERANT TRANSCEIVER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發(fā)器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| TJA1054T/N1 | 制造商:NXP Semiconductors 功能描述:DATACOM, INTERFACE CIRCUIT, PDSO14 |
| TJA1054T/N1,512 | 功能描述:網絡控制器與處理器 IC CAN XCVR FAULT-TOL RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發(fā)器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發(fā)布緊急采購，3分鐘左右您將得到回復。