參數資料
型號： TIGER560
廠商： Electronic Theatre Controls, Inc.
英文描述： USB Controller for Low Cost VoIP solutions
中文描述： USB控制器的低成本VoIP解決方案
文件頁數： 17/37頁
文件大小： 449K
代理商： TIGER560
Tiger560
Advance Information
Revision 1.1 released on 2/20/01
Page 17
Serial Port Interface
The Tiger560 serial port consists of one data clock (DCLK), one frame synchronization clock
(FSC) and two data lines (DIN and DOUT).
DCLK and FSC can either be inputs or outputs to the Tiger560. DCLK can either be the same as
the data rate or twice the data rate. If DCLK is the same as the data rate the internal clock
doubler should be turned on for correct operation.
The serial port interface is controlled by two sets of registers based on the Tiger560 chip mode
selection.
If Tiger560 is set to use original Tiger500 USB descriptor mode(HA[3:2]==2’b00), the serial port
interface is controlled by the same set of registers as Tiger500. If Tiger560 is set to use the
Tiger560 USB descriptor (HA[3:2]==2’b01) and the audio class device is enabled
(productID[15:14] == 2’b01 or 2’b10), the serial port interface is controlled by productID definition
and a set of registers that is specific to the Tiger560. For detailed register definition please see
the registers section.
Tiger500 mode: Serial port signals
The FSC input should be an 8 KHz clock. Within one FSC period, the first 32 bits of data are
transmitted and received. The data is clocked in and out on by the DCLK. For details on the serial
port timing please see the timing diagram in the section on A.C. characteristics.
DOUT is open-collector, it should be pulled high with an external pull-up resistor. Outside the 32
bit data transfer window, DOUT pins can be forced to drive low by setting bit 3 in register 0x01.
This option allows certain types of peripherals to activate the data clock.
Tiger500 mode: Serial port data transfer
Tiger560 USB Endpoint 3 and Endpoint 4 are used for the serial port data transfer. Each pipe will
transfer 37 bytes of data each USB isochronous transfer. Endpoint 3 will communicate the serial
port data back to host and Endpoint 4 will transfer output data to serial port.
The serial port clock is asynchronous to the USB clock, so an adaptive endpoint design is used.
Endpoint 3 provides the data rate information and feedback to the host. Host receives the data
rate information and decides the transfer rate to Endpoint 4. The data rate information is in the
byte one of the transferred data stream. Three possible value are defined, 32, 28 and 36. For 8
KHz of frame clock, every 1 ms, 32 bytes of data will be transferred. Endpoint 3 will adjust the
transfer count with either 28 or 36 based on the difference between the serial port clock and USB
clock.
The host is required to send the same amount of data to Endpoint 4 for the synchronization. Both
endpoints have the same data format. The first byte is the number of valid data bytes. The
following bytes are the valid data. Stuff bytes are attached at end of valid data so the total number
of bytes is 37.
125uS
32 bits
FSC
DIN
DOUT
相關PDF資料
PDF描述
TIL181(中文) Optocouplers(標準6腳光耦)
TIL186-1(中文) Optocouplers(AC輸入光耦)
TIL186-2(中文) Optocouplers(AC輸入光耦)
TIL186-3(中文) Optocouplers(AC輸入光耦)
TIL186-4(中文) Optocouplers(AC輸入光耦)
相關代理商/技術參數
參數描述
TIGER5B-1C-WH-C 制造商:Carling Technologies 功能描述:TIL, G, H, I-SERIES RKR SW - Bulk
TIGER5B-6M-BL-NBL-XHG1 制造商:Carling Technologies 功能描述:TIL, G, H, I-SERIES RKR SW - Bulk
TIGER5E-6S-BL-MBL-XTSP1 制造商:Carling Technologies 功能描述:TIL, G, H, I-SERIES RKR SW - Bulk
TIGER5E-6S-BL-NBL 制造商:Carling Technologies 功能描述:TIL, G, H, I-SERIES RKR SW - Bulk
TIGER5E-6S-BL-NBL-XTS1 制造商:Carling Technologies 功能描述:TIL, G, H, I-SERIES RKR SW - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*