參數資料
型號： THS4011MFK
廠商： Texas Instruments, Inc.
英文描述： 290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS
中文描述： 290 - MHz的低失真高速放大器
文件頁數： 21/30頁
文件大小： 439K
代理商： THS4011MFK
THS4011, THS4012
290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS
SLOS216B – JUNE 1999 – FEBRUARY 2000
21
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
general PowerPAD design considerations (continued)
DIE
Side View (a)
End View (b)
Bottom View (c)
DIE
Thermal
Pad
NOTE A: The thermal pad is electrically isolated from all terminals in the package.
Figure 33. Views of Thermally Enhanced DGN Package
Although there are many ways to properly heatsink this device, the following steps illustrate the recommended
approach.
Thermal pad area (68 mils x 70 mils) with 5 vias
(Via diameter = 13 mils)
Figure 34. PowerPAD PCB Etch and Via Pattern
1.
Prepare the PCB with a top side etch pattern as shown in Figure 34. There should be etch for the leads as
well as etch for the thermal pad.
2.
Place five holes in the area of the thermal pad. These holes should be 13 mils in diameter. Keep them small
so that solder wicking through the holes is not a problem during reflow.
3.
Additional vias may be placed anywhere along the thermal plane outside of the thermal pad area. This helps
dissipate the heat generated by the THS401xDGN IC. These additional vias may be larger than the 13-mil
diameter vias directly under the thermal pad. They can be larger because they are not in the thermal pad
area to be soldered so that wicking is not a problem.
4.
Connect all holes to the internal ground plane.
5.
When connecting these holes to the ground plane,
do
not
use the typical web or spoke via connection
methodology. Web connections have a high thermal resistance connection that is useful for slowing the heat
transfer during soldering operations. This makes the soldering of vias that have plane connections easier.
In this application, however, low thermal resistance is desired for the most efficient heat transfer. Therefore,
the holes under the THS401xDGN package should make their connection to the internal ground plane with
a complete connection around the entire circumference of the plated-through hole.
6.
The top-side solder mask should leave the terminals of the package and the thermal pad area with its five
holes exposed. The bottom-side solder mask should cover the five holes of the thermal pad area. This
prevents solder from being pulled away from the thermal pad area during the reflow process.
7.
Apply solder paste to the exposed thermal pad area and all of the IC terminals.
8.
With these preparatory steps in place, the THS401xDGN IC is simply placed in position and run through
the solder reflow operation as any standard surface-mount component. This results in a part that is properly
installed.
相關PDF資料
PDF描述
THS4012D 290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS
THS4012DGN 290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS
THS4012EVM 290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS
THS4021D 350-MHz LOW-NOISE HIGH-SPEED AMPLIFIERS
THS4021DGN 350-MHz LOW-NOISE HIGH-SPEED AMPLIFIERS
相關代理商/技術參數
參數描述
THS4011MFKB 制造商:Texas Instruments 功能描述:290-MHZ LOW-DISTORTION VOLTAGE-FEEDBACK
THS4011MJG 制造商:Texas Instruments 功能描述:OP AMP SGL VOLT FDBK 16.5V/33V 8CDIP - Rail/Tube
THS4011MJGB 制造商:Texas Instruments 功能描述:OP Amp Single Volt Fdbk ±16.5V/33V 8-Pin CDIP Tube 制造商:Texas Instruments 功能描述:OP AMP SGL VOLT FDBK 16.5V/33V 8CDIP - Rail/Tube
THS4012 制造商:TI 制造商全稱:Texas Instruments 功能描述:290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS
THS4012CD 功能描述:高速運算放大器 Dual 290MHz RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*