參數資料
型號： STLED316SMTR
廠商： STMICROELECTRONICS
元件分類： 顯示控制器
英文描述： 4 X 17 SEGMENTS SEGMENT LED DRVR AND DSPL CTLR, PDSO24
封裝： ROHS COMPLIANT, SOP-24
文件頁數： 9/33頁
文件大小： 438K
代理商： STLED316SMTR
STLED316S
Key-scan & display cycle
17/33
6
Key-scan & display cycle
The display RAM stores the data transmitted from an external device to the STLED316S
through the serial interface. Refer to Section 9: Key-scanning and display timing on page 25
for a pictorial representation.
The grid and segment outputs are controlled by the display output module. The entire grid
will be turned off on channel 1/16 and 16/16 meaning that the first channel and last channel
are off. This is referred to as blanking time.
During the keyscan time (first cycle from timing generator), the entire grid is turned off and
only the segments are enabled one by one (seg0 to seg7). The segment on time is 64 s.
During the LED discrete time (second cycle), the data present on the internal LED buffer is
checked. If the data is present, then the brightness setting of each LED in the brightness
control register is checked. Then each segment will be enabled or disabled based on the
register value. In this duration, the grids 1 to 6 are turned off. The grid corresponding to LED
digit is turned on. The LED on duty cycle is 14/16. If the LED/seg1 brightness is 12/16, it
means that the segment1 OFF time is 12/16 and on time is 2/16.
During 7-segment display time (3rd cycle to 8th cycle), the display status is checked whether
it is ON or OFF. If display is ON, then the dimming settings are checked from the
configuration register for the grid (it may be common dimming setting or individual dimming
setting for each digit). The minimum turn on time is 1/16 and maximum turn on time is 14/16.
The blanking time is valid before the turning on and turning off of the grid. The blanking
interval is 32 s. This will continue until the maximum number of digits configured in the
register. Once the full cycle is complete, the keyscan cycle will start again.
If the display is not turned on, then the timing generation will immediately go to the key scan
mode.
Initial:
All the segments and grids are turned off.
During operation:
1.
Turn on segment (keyscan) one by one. On time duration is 64 s.
2.
Check the data present in LED register. If data is present, turn on the respective LED
grid and segments.
3.
Check the display on. If display is turned on, then enable the grid one by one from grid
1 to grid 6 (maximum) and turn on segments.
相關PDF資料
PDF描述
STM32F101C8T6 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP48
STM32F101R6T6 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP64
STM32F101VBT6 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP100
STM32F101T6U6 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, QCC36
STM32F101CBT6AXX 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP48
相關代理商/技術參數
參數描述
STLED325QTR 功能描述:LED照明驅動器 I2C interfaced LED controller/driver RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N
STLED32MAT-EVAL1 功能描述:BOARD EVALUATION FOR LED ARRAY RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
STLED524 功能描述:IC MATRIX LED DISPL DVR 56CSP 制造商:stmicroelectronics 系列:- 包裝:剪切帶（CT） 零件狀態:有效 顯示類型:LED 配置:點陣 接口:SPI 數字或字符:- 電流 - 電源:- 電壓 - 電源:2.7 V ~ 5.5 V 工作溫度:-30°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:56-UFBGA，WLCSP 供應商器件封裝:56-CSP（3.4x3.0） 標準包裝:1
ST-LEQ1 制造商:Radio Design Labs 功能描述:Use With Vca Loudne Equalizer 制造商:RADIO DESIGN LABS 功能描述:LOUDNESS EQUALIZER USE WITH VCA
STLGCA-1.024 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Crystal Oscillator
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*