參數資料
型號: STLED316SMTR
廠商: STMICROELECTRONICS
元件分類: 顯示控制器
英文描述: 4 X 17 SEGMENTS SEGMENT LED DRVR AND DSPL CTLR, PDSO24
封裝: ROHS COMPLIANT, SOP-24
文件頁數: 4/33頁
文件大?。?/td> 438K
代理商: STLED316SMTR
STLED316S functional description
STLED316S
12/33
3.8
LED drivers
The constant current capability is up to 40 mA per output segment and is set for all the
outputs using a single external resistor. When acting as digit drivers, the outputs source
current to the display anodes. When acting as segment drivers, the LED outputs sink current
from the display cathodes. The outputs are high impedance when not being used as digit or
segment drivers.
Each port configured as a LED digit driver behaves as a digitally-controlled constant current
sink. The LED drivers are suitable for both discrete LEDs and common anode (CA) numeric
LED digits. When fully configured as a LED driver, the STLED316S controls up to 8 LED
segments in a single digit with 8-step logarithmic brightness control for the digits. A single
resistor sets the maximum segment current for all the segments, with a maximum of 40mA
per segment. The STLED316S drives any combination of discrete LEDs and CA digits for
numeric displays.
The recommended value of RSET is the minimum allowed value, since it sets the display
driver to the maximum allowed segment current. RSET can be a higher value to set the
segment current to a lower maximum value where desired. The user must also ensure that
the maximum current specifications of the LEDs connected to the drivers are not exceeded.
The brightness of the individual digits in the display panel can be controlled separately.
3.9
Interrupt
The device includes an active low level IRQ_N pin to the microprocessor. The STLED316S
generates an interrupt when a key is pressed.
3.10
Operating the device with 3.3 V interface voltages
The device can detect the input voltage levels reference to 3.3 V from the main controller
chip as long as the VIL and VIH specifications of the STLED316S are met. If the input
voltage to STLED316S is greater than 2.9 V, the STLED316S will recognize the signal level
as a valid high and if the input voltage is lower than 1.75 V, it will be recognized as a valid
low level.
For the output signals from the device like DOUT and IRQ_N, the signal level depends on
the external supply to which the external pull up resistor is connected to. Thus this
eliminates the use of any level shifter between the main controller and the STLED316S.
相關PDF資料
PDF描述
STM32F101C8T6 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP48
STM32F101R6T6 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP64
STM32F101VBT6 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP100
STM32F101T6U6 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, QCC36
STM32F101CBT6AXX 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP48
相關代理商/技術參數
參數描述
STLED325QTR 功能描述:LED照明驅動器 I2C interfaced LED controller/driver RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N
STLED32MAT-EVAL1 功能描述:BOARD EVALUATION FOR LED ARRAY RoHS:否 類別:編程器,開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像,彩色(RGB) 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
STLED524 功能描述:IC MATRIX LED DISPL DVR 56CSP 制造商:stmicroelectronics 系列:- 包裝:剪切帶(CT) 零件狀態:有效 顯示類型:LED 配置:點陣 接口:SPI 數字或字符:- 電流 - 電源:- 電壓 - 電源:2.7 V ~ 5.5 V 工作溫度:-30°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:56-UFBGA,WLCSP 供應商器件封裝:56-CSP(3.4x3.0) 標準包裝:1
ST-LEQ1 制造商:Radio Design Labs 功能描述:Use With Vca Loudne Equalizer 制造商:RADIO DESIGN LABS 功能描述:LOUDNESS EQUALIZER USE WITH VCA
STLGCA-1.024 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Crystal Oscillator