參數資料
型號： ST78C36
廠商： Exar Corporation
英文描述： ECP/EPP Parallel Printer Port with 16 Byte FIFO(ECP/EPP并行打印機端口（帶16字節先進先出）)
中文描述： 支持ECP / EPP并行打印機端口（支持ECP / EPP并行打印機端口（帶16字節先進先出），16字節FIFO）
文件頁數： 10/27頁
文件大小： 204K
代理商： ST78C36
ST78C36/36A
6-30
Rev. 4.20
0 = At least one byte of data contains in the FIFO.
1 = FIFO is empty.
ECR Bit-1:
This read-only bit returns FIFO full status (FIFO-F)
and is forced low unless PPF, ECP, or TST mode is
selected.
0 = At least one empty location is available in the
FIFO.
1 = FIFO is full.
ECR Bit-2:
When low, this bit (ServiceIntr) enables a pulsed
interrupt and enables DMA requests (if bit-3 is set). If
the enabled interrupt occurs, this bit is automatically
returned to a high. The interrupt conditions are:
ECR Bit-3 = DMA
DCR Bit-5 = DIRection
DMA
DIR
CONDITION
0
0
1
0
1
X
8 empty bytes in the FIFO.
8 filled bytes in the FIFO.
DMA Terminal Count (TC).
ECR BIT-3:
This bit disables DMA when set low. When set high,
a low on ServiceIntr will enable DMA requests.
0 = DMA disabled, DRQx pin is three-stated.
1 = DMA enabled
ECR Bit-4:
When low, this bit (-ErrIntrEn) enables a pulsed inter-
rupt if -ERROR (-Fault) is low. The interrupt is only
enabled in ECP mode.
ECR Bit 5-7:
This field can be set to any value if the current value
is 000 or 001. If the current value is not 000 or 001,
then the field can only be written to 000 or 001. The
modes are defined as:
Cnfg-B Bit 0-2:
With bit 2 forced low, select an 8-bit DMA channel per
the following table:
-IOW
-IOR
DMA
X00
X01
X10
X11
000
001
010
011
3
1
2
3 (default)
Cnfg-B Bit 3-5:
Select an IRQ channel per the following table:
-IOW
-IOR
IRQ
000
001
010
011
100
101
110
111
001
001
010
001
001
001
001
111
7
7 (default)
9
7
7
7
7
5
Cnfg-B Bit-6:
Returns the true value of the selected IRQ pad.
Cnfg-B Bit-7:
Indicates RLE compression is not supported.
EXTENDED CONTROL REGISTER ( ECR )
The Extended Control Register has a system RESET
state of 10010101. The significance of the bits is
defined by the ECP specification as:
ECR Bit-0:
This read-only bit returns FIFO empty status (FIFO-E)
and is forced high unless PPF, ECP, or TST mode is
selected.
相關PDF資料
PDF描述
ST78C36A ECP/EPP Parallel Printer Port with 16 Byte FIFO(ECP/EPP并行打印機端口（帶16字節先進先出）)
ST7LITE05Y0B6 FUSE, FORK LIFT TRUCK, 50A; Current, fuse rating:50A; Voltage rating, DC:80V; Approval category:DIN 43560/1; Depth, external:20mm; Height:1mm; Length / Height, external:0.5mm; Width, external:82mm RoHS Compliant: Yes
ST7LITE05Y0M6 FUSE, FORK LIFT TRUCK, 80A; Current, fuse rating:80A; Voltage rating, DC:80V; Approval category:DIN 43560/1; Depth, external:20mm; Height:1mm; Length / Height, external:0.5mm; Width, external:82mm RoHS Compliant: Yes
ST7LITE09Y0B6 FUSE, FORK LIFT TRUCK, 200A; Current, fuse rating:200A; Voltage rating, DC:80V; Approval category:DIN 43560/1; Depth, external:20mm; Height:1mm; Length / Height, external:0.5mm; Width, external:82mm RoHS Compliant: Yes
ST7LITE09Y0M6 FUSE, FORK LIFT TRUCK, 250A; Current, fuse rating:250A; Voltage rating, DC:80V; Approval category:DIN 43560/1; Depth, external:20mm; Height:1mm; Length / Height, external:0.5mm; Width, external:82mm RoHS Compliant: Yes
相關代理商/技術參數
參數描述
ST78C36_05 制造商:EXAR 制造商全稱:EXAR 功能描述:ECP/EPP PARALLEL PRINTER PORT WITH 16-BYTE FIFO
ST78C36A 制造商:EXAR 制造商全稱:EXAR 功能描述:ECP/EPP PARALLEL PRINTER PORT WITH 16-BYTE FIFO
ST78C36ACJ-0A-EVB 功能描述:界面開發工具 Supports 78C36A 44ld PLCC, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
ST78C36ACJ44 制造商:EXAR 制造商全稱:EXAR 功能描述:ECP/EPP PARALLEL PRINTER PORT WITH 16-BYTE FIFO
ST78C36ACJ44-F 功能描述:接口 - 專用 UART RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*