參數資料
型號： ST72141K2B3/XXX
廠商： STMICROELECTRONICS
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32
封裝： 0.400 INCH, PLASTIC, SDIP-32
文件頁數： 76/133頁
文件大?。?/td> 2615K
代理商： ST72141K2B3/XXX
Obsolete
Product(s)
- Obsolete
Product(s)
ST72141K2
47/133
MOTOR CONTROLLER (Cont’d)
Demagnetization (D) Event
At the end of the demagnetization phase, current
no longer goes through the free-wheeling diodes.
The voltage on the non-excited winding terminal
goes from one of the power rail voltages to the
common star connection voltage plus the BEMF
voltage. In some cases (if the BEMF voltage is
positive and the free-wheeling diodes are at
ground for example) this end of demagnetization
can be seen as a voltage edge on the selected
MCIx input and it is called a hardware demagneti-
zation event DH. See Table 13.
If enabled by the HDM bit in the MCRB register,
the current value of the MTIM timer is captured in
register MDREG when this event occurs in order
to be able to simulate the demagnetization phase
for the next steps.
When enabled by the SDM bit in the MCRB regis-
ter, demagnetization can also be simulated by
comparing the MTIM timer with the MDREG regis-
ter. This kind of demagnetization is called software
demagnetization DS.
If the HDM and SDM bits are both set, the first
event that occurs, triggers a demagnetization
event. For this to work correctly, a DS event must
not precede a DH event because the latter could
be detected as a Z event.
Software demagnetization can also be always
used if the HDM bit is reset and the SDM bit is set.
This mode works as a programmable masking
time between the C and Z events. To drive the mo-
tor securely, the masking time must be always
greater than the real demagnetization time in order
to avoid a spurious Z event.
When an event occurs, (either DH or DS) the DI bit
in the MISR register is set and an interrupt request
is generated if the DIM bit of register MIMR is set.
Warning 1: Due to the alternate automatic capture
and compare of the MTIM timer with MDREG reg-
ister by DH and DS events, the MDREG register
should be manipulated with special care.
Warning 2: To avoid a system stop, the value writ-
ten to the MDREG register in Soft Demagnetiza-
tion Mode (SDM = 1) should always be:
– Greater than the MCOMP value of the commuta-
tion before the related demagnetization
– Greater than the value in the MTIM counter at
that moment (when writing to the MDREG regis-
ter).
Figure 30. D Event Generation Mechanism
MTIM [8-bit Up Counter]§
DS
MDREG [Dn]
§
Compare
8
DH
DS
HDM bit
D = DH & HDM bit + DS & SDM bit
DH
SDM bit
F(x)
D
§ Register updated on R event
SDM bit
HDMn bit*
DH
or
1
2
20 s / C
CPBn bit*
C
DS,H
Sample
To Z event detection
SR bit
20
s
/
C
* = Preload register, changes taken into account at next C event
To interrupt generator
MCRA Register
MCRB Register
相關PDF資料
PDF描述
ST72311N4T6/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64
ST72311J2B6/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42
ST72311N2T3/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64
ST72321BAR7T6 MICROCONTROLLER, QFP64
ST72321BR7T3 MICROCONTROLLER, QFP64
相關代理商/技術參數
參數描述
ST72141K2B6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCU WITH ELECTRIC-MOTOR CONTROL, ADC, 16-BIT TIMERS, SPI INTERFACE
ST72141K2M1 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCU WITH ELECTRIC-MOTOR CONTROL, ADC, 16-BIT TIMERS, SPI INTERFACE
ST72141K2M3 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCU WITH ELECTRIC-MOTOR CONTROL, ADC, 16-BIT TIMERS, SPI INTERFACE
ST72141K2M3/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller
ST72141K2M6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCU WITH ELECTRIC-MOTOR CONTROL, ADC, 16-BIT TIMERS, SPI INTERFACE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*