- 您現在的位置：買賣IC網 > PDF目錄299943 > ST52501LF2 MAX 7000 CPLD 128 MC 100-TQFP PDF資料下載
參數資料
| 型號： | ST52501LF2 |
| 英文描述： | MAX 7000 CPLD 128 MC 100-TQFP |
| 中文描述： | 8位紅外驅動重癥監護病房。定時器/脈寬調制。 I2C總線。的SPI。脊髓損傷。低電壓 |
| 文件頁數： | 105/106頁 |
| 文件大小： | 1355K |
| 代理商： | ST52501LF2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁當前第105頁第106頁
98/106
is taking place with an external device. When this
occurs, the transfer continues uninterrupted; and
the software writing will be unsuccessful.
Write collisions can occur both in master and slave
mode.
Note: a “read collision” will never occur since the
data byte received is placed in a buffer, in which
access is always synchronous with the ICU
operation.
In Slave mode
When the CPHA bit is set:
The slave device will receive a clock (SCK) edge
prior to the latch of the first data transfer. This first
clock edge will freeze the data in the slave device
SPI_OUT register and output the MSBit on to the
external MISO pin of the slave device.
The SS pin low state enables the slave device, but
the output of the MSBit onto the MISO pin does not
take place until the first data transfer clock edge
occurs.
When the CPHA bit is reset:
Data is latched on the occurrence of the first clock
transition. The slave device doesn’t have a way of
knowing when that transition will occur; therefore,
the slave device collision occurs when software
attempts to write the SPI_OUT register after its SS
pin has been pulled low.
For this reason, the SS pin must be high, between
each data byte transfer, in order to allow the CPU
to write in the SPI_OUT register without generating
a write collision.
In Master mode
Collision in the master device is defined as a write
of the SPI_OUT register, while the internal serial
clock (SCK) is in the process of transfer.
The SS pin signal must always be high on the
master device.
Figure 14.3 CHPA/SS Timing Diagram
WCOL bit
The WCOL bit in the SPI_STATUS_CR register is
set if a write collision occurs.
No SPI interrupt is generated when the WCOL bit
is set (the WCOL bit is a status flag only).
The WCOL bit is cleared by a software sequence
(see Section 14.5).
14.4.5 Master Mode Fault.
Master mode fault occurs when the master device
has its SS pin pulled low, then the MODF bit is set.
Master mode fault affects the SPI peripheral in the
following ways:
– The MODF bit is set and an SPI interrupt is
generated if the SPIE bit is set.
– The SPE bit is reset. This blocks all output from
the device and disables the SPI peripheral.
– The MSTR bit is reset, forcing the device into
slave mode.
Clearing the MODF bit is done through a software
sequence:
1. A read or write access to the SPI_STATUS_CR
register while the MODF bit is set.
2. A write to the SPI_CR register.
Note: To avoid any multiple slave conflicts in the
case of a system comprising several MCUs, the
SS
pin must be pulled high during the clearing
sequence of the MODF bit. The SPE and MSTR
bits may be restored to their original state during or
after this clearing sequence.
Hardware does not allow the user to set the SPE
and MSTR bits, while the MODF bit is set (except
in the MODF bit clearing sequence).
In a slave device the MODF bit can’t be set, but in
a multi master configuration the device can be in
slave mode with this MODF bit set.
The MODF bit indicates that there might have been
a multi-master conflict for system control and
allows a proper exit from system operation to a
reset or default system state using an interrupt
routine.
MOSI/MISO
Master SS
Slave SS
(CPHA=0)
Slave SS
(CPHA=1)
Byte 1
Byte 2
Byte 3
相關PDF資料 |
PDF描述 |
|---|---|
| ST52501LF3 | MAX 7000 CPLD 128 MC 100-PQFP |
| ST52501LG1 | MAX 7000 CPLD 128 MC 160-PQFP |
| ST52501LG2 | MAX 7000 CPLD 128 MC 100-TQFP |
| ST52501LG3 | MAX 7000 CPLD 128 MC 100-TQFP |
| ST52501LK1 | MAX 7000 CPLD 160 MC 84-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST52501LF3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT ICU WITH IR DRIVER. TIMER/PWM. I2C. SPI. SCI. LOW VOLTAGE |
| ST52501LG1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT ICU WITH IR DRIVER. TIMER/PWM. I2C. SPI. SCI. LOW VOLTAGE |
| ST52501LG2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT ICU WITH IR DRIVER. TIMER/PWM. I2C. SPI. SCI. LOW VOLTAGE |
| ST52501LG3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT ICU WITH IR DRIVER. TIMER/PWM. I2C. SPI. SCI. LOW VOLTAGE |
| ST52501LK1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT ICU WITH IR DRIVER. TIMER/PWM. I2C. SPI. SCI. LOW VOLTAGE |
發布緊急采購，3分鐘左右您將得到回復。