- 您現在的位置：買賣IC網 > PDF目錄383837 > ST16C452PS (Exar Corporation) Dual UART with Parallel Printer Port(雙通用異步接收器/發送器（帶并行打印機端口）) PDF資料下載
參數資料
| 型號： | ST16C452PS |
| 廠商： | Exar Corporation |
| 英文描述： | Dual UART with Parallel Printer Port(雙通用異步接收器/發送器（帶并行打印機端口）) |
| 中文描述： | 雙UART與并行打印機端口（雙通用異步接收器/發送器（帶并行打印機端口）） |
| 文件頁數： | 6/30頁 |
| 文件大小： | 389K |
| 代理商： | ST16C452PS |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
6
ST16C452/452PS
Rev. 3.10
Symbol
Pin
Signal Type
Pin Description
connected with a printer to select the printer with an active
low.
-STROBE
55
I/O
Strobe (open drain, with internal pull-up) - General purpose
I/O or data strobe output. Normally this output is connected
to a printer and indicates that valid data is available at the
printer port (PD0-PD7).
N.C.
22,42
Not Used. Should be left open.
VCC
23,40,64
Pwr
Power supply input.
-CD A/B
29,8
I
Carrier Detect (active low) - These inputs are associated
with individual UART channels A through B. A logic 0 on this
pin indicates that a carrier has been detected by the modem
for that channel.
-CTS A/B
28,13
I
Clear to Send (active low) - These inputs are associated with
individual UART channels, A through B. A logic 0 on this
pin(s) indicates the modem or data set is ready to accept
transmit data from the 452/452PS for the given channel.
Status can be tested by reading MSR bit-4 for that
channel(s). -CTS has no effect on the transmit or receive
operation.
-DSR A/B
31,5
I
Data Set Ready (active low) - These inputs are associated
with individual UART channels, A through B. A logic 0 on
this pin(s) indicates the modem or data set is powered-on
and is ready for data exchange with the UART. This pin has
no effect on the UARTs transmit or receive operation.
-DTR A/B
25,11
O
Data Terminal Ready (active low) - These outputs are
associated with individual UART channels, A through B. A
logic 0 on this pin(s) indicates that the 452/452PS is
powered-on and ready. This pin can be controlled via the
modem control register for channel(s) A-B. Writing a logic
1 to MCR bit-0 will set the -DTR output to logic 0, enabling
the modem. This pin will be a logic 1 after writing a logic 0
to MCR bit-0, or after a reset. This pin has no effect on the
UARTs transmit or receive operation.
SYMBOL DESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C452 | Dual UART with Parallel Printer Port(雙通用異步接收器/發送器（帶并行打印機端口）) |
| ST16C550 | UART with 16-Byte FIFO(通用異步接收器/發送器（帶16字節的先進先出）) |
| ST16C552 | Dual UART with 16-Byte FIFO and Parallel Printer Port(雙通用異步接收器/發送器（帶16字節的先進先出和并行打印機端口）) |
| ST16C552A | Dual UART with 16-Byte FIFO and Parallel Printer Port(雙通用異步接收器/發送器（帶16字節的先進先出和并行打印機端口）) |
| ST16C554DCJ68 | QUAD UART WITH 16-BYTE FIFOS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C454 | 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
| ST16C454_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
| ST16C454CJ | 制造商:Exar Corporation 功能描述: |
| ST16C454CJ-0A-EVB | 功能描述:界面開發工具 Supports C454 68 ld PLCC, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| ST16C454CJ68 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。