- 您現在的位置：買賣IC網 > PDF目錄383837 > ST16C452IJ68PS (EXAR CORP) DUAL UART WITH PARALLEL PRINTER PORT PDF資料下載
參數資料
| 型號： | ST16C452IJ68PS |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | DUAL UART WITH PARALLEL PRINTER PORT |
| 中文描述： | 2 CHANNEL(S), 1.5M bps, SERIAL COMM CONTROLLER, PQCC68 |
| 封裝： | PLASTIC, LCC-68 |
| 文件頁數： | 4/30頁 |
| 文件大?。?/td> | 162K |
| 代理商： | ST16C452IJ68PS |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
4
ST16C452/452PS
Rev. 3.20
SYMBOL DESCRIPTION
Symbol
Pin
Signal Type
Pin Description
-ERROR
63
I
Error, Printer (with internal pull-up) - General purpose input
or line printer error. This pin may be connected to the active
low (logic 0) output of a printer to indicate an error condition.
GND
2,7,54
27
Pwr
Signal and Power Ground.
INIT
57
I/O
Initialize (open drain, with internal pull-up) - General pur-
pose I/O signal. This pin may be connected for initialization
service of a connected line printer. Generally when this
signal is a logic 0, any connected printer will be initialized.
INT A/B
45,60
O
Interrupt output A/B ( three state active high) - These pins
provide individual channel interrupts, INT A-B. INT A-B are
enabled when MCR bit-3 is set to a logic 1, interrupts are
enabled in the interrupt enable register (IER), and when an
interrupt condition exists. Interrupt conditions include: re-
ceiver errors, available receiver buffer data, transmit buffer
empty, or when a modem status flag is detected.
-INTP
59
O
Printer Interrupt, - This pin can be used to signal the
interrupt status of a connected printer. This pin basically
tracks the -ACK input pin, When INTSEL is a logic 0 and
interrupts are enabled by bit-4 in the control register. A
latched mode can be selected by setting INTSEL to a logic
1. In this case the interrupt -INTP is generated normally but
does not return to the inactive state until the trailing edge of
the read cycle (-IOR pin). -INTP is three stated until CON
bit-4 is set to a logic 1.
INTSEL
43
I
Interrupt Select mode - This pin selects the interrupt type for
the printer port (-INTP). When this pin is a logic 0, the
external -ACK signal state is generally followed, minus
some minor propagation delay. Making this pin a logic 1 or
connecting it to VCC will set the interrupt latched mode. In
this case the printer interrupt (-INTP) will not return to a logic
1 until the trailing edge of -IOR (end of the external CPU
read cycle).
-IOR
37
I
Read strobe.- A logic 0 transition on this pin will place the
contents of an Internal register defined by address bits A0-A2
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C452CJ68 | Power Supply IC; Number of Outputs:1; Supply Voltage Max:5.5V; Package/Case:10-MSOP; Leaded Process Compatible:No; Output Current:150mA; Output Voltage Max:1.3V; Peak Reflow Compatible (260 C):No; Power Dissipation:481mW |
| ST16C452CJ68PS | Power Supply IC; Number of Outputs:1; Supply Voltage Max:5.5V; Package/Case:10-MSOP; Leaded Process Compatible:No; Output Current:150mA; Output Voltage Max:1.3V; Peak Reflow Compatible (260 C):No; Power Dissipation:481mW |
| ST16C452PS | Dual UART with Parallel Printer Port(雙通用異步接收器/發送器（帶并行打印機端口）) |
| ST16C452 | Dual UART with Parallel Printer Port(雙通用異步接收器/發送器（帶并行打印機端口）) |
| ST16C550 | UART with 16-Byte FIFO(通用異步接收器/發送器（帶16字節的先進先出）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C452IJ68PS-F | 功能描述:UART 接口集成電路 DUAL UART W/PARALEL PRINTER PORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C452IJ68TR-F | 制造商:Exar Corporation 功能描述:UART 2-CH 3.3V/5V 68-Pin PLCC T/R 制造商:Exar Corporation 功能描述:ST16C452IJ68TR-F |
| ST16C452PS | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH PARALLEL PRINTER PORT |
| ST16C454 | 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
| ST16C454_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
發布緊急采購，3分鐘左右您將得到回復。