- 您現在的位置：買賣IC網 > PDF目錄16478 > ST16C2550CQ-0A-EB (Exar Corporation)EVAL BOARD FOR ST16C2550 PDF資料下載
參數資料
| 型號： | ST16C2550CQ-0A-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 11/37頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR ST16C2550 |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
ST16C2550
19
REV. 4.4.1
2.97V TO 5.5V DUART WITH 16-BYTE FIFO
4.4
Interrupt Status Register (ISR) - Read-Only
The UART provides multiple levels of prioritized interrupts to minimize external software interaction. The
Interrupt Status Register (ISR) provides the user with four interrupt status bits. Performing a read cycle on the
ISR will give the user the current highest pending interrupt level to be serviced, others are queued up to be
serviced next. No other interrupts are acknowledged until the pending interrupt is serviced. The Interrupt
Source Table, Table 8, shows the data values (bits 0-3) for the interrupt priority levels and the interrupt sources
associated with each of these interrupt levels.
4.4.1
Interrupt Generation:
LSR is by any of the LSR bits 1, 2, 3 and 4.
RXRDY is by RX trigger level.
RXRDY Time-out is by a 4-char plus 12 bits delay timer.
TXRDY is by TX FIFO empty.
MSR is by any of the MSR bits 0, 1, 2 and 3.
4.4.2
Interrupt Clearing:
LSR interrupt is cleared by a read to the LSR register.
RXRDY interrupt is cleared by reading data until FIFO falls below the trigger level.
RXRDY Time-out interrupt is cleared by reading RHR.
TXRDY interrupt is cleared by a read to the ISR register or writing to THR.
MSR interrupt is cleared by a read to the MSR register.
]
TABLE 8: INTERRUPT SOURCE AND PRIORITY LEVEL
PRIORITY LEVEL
ISR REGISTER STATUS BITS
SOURCE OF INTERRUPT
BIT-3
BIT-2
BIT-1
BIT-0
1
0
1
0
LSR (Receiver Line Status Register)
2
1
0
RXRDY (Receive Data Time-out)
3
0
1
0
RXRDY (Received Data Ready)
4
0
1
0
TXRDY (Transmit Ready)
5
0
MSR (Modem Status Register)
-
0
1
None (default)
ISR[0]: Interrupt Status
Logic 0 = An interrupt is pending and the ISR contents may be used as a pointer to the appropriate interrupt
service routine.
Logic 1 = No interrupt pending (default).
ISR[3:1]: Interrupt Status
These bits indicate the source for a pending interrupt at interrupt priority levels (See Table 8).
ISR[5:4]: Reserved
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are
enabled.
相關PDF資料 |
PDF描述 |
|---|---|
| LBC2518T331M | INDUCTOR WOUND 330UH 65MA 1007 |
| SP809EK-L-2-6/TR | IC MPU RESET CIRC 2.6V SOT23-3 |
| RBM15DTKI | CONN EDGECARD 30POS DIP .156 SLD |
| M1DXK-2040K | IDC CABLE - MKR20K/MC20F/X |
| L-14W2N0SV4E | WIREWOUND INDUCTOR 2NH 0603 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C2550CQ-0B-EB | 功能描述:界面開發工具 Supports C2550 48 ld TQFP, PCI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| ST16C2550CQ48 | 制造商:Exar Corporation 功能描述: |
| ST16C2550CQ48-F | 功能描述:UART 接口集成電路 2.97V-5.5V 16B FIFO temp 0C to 70C; UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C2550CQ48TR-F | 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C2550IJ44 | 制造商:Exar Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。