- 您現在的位置：買賣IC網 > PDF目錄383820 > SN74GTLP1394DGVR Bus Exchanger PDF資料下載
參數資料
| 型號： | SN74GTLP1394DGVR |
| 英文描述： | Bus Exchanger |
| 中文描述： | 總線交換 |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 234K |
| 代理商： | SN74GTLP1394DGVR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁
SN74GTLP1394
2-BIT LVTTL-TO-GTLP ADJUSTABLE-EDGE-RATE BUS TRANSCEIVER
WITH SPLIT LVTTL PORT FEEDBACK PATH, AND SELECTABLE POLARITY
SCES286E
–
OCTOBER 1999
–
REVISED AUGUST 2001
11
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
operational description
The GTLP1394 is specifically designed for use with the Texas Instruments 1394 backplane layer controller
family to transmit the 1394 backplane serial bus across parallel backplanes. But, it is a versatile 2-bit device
that also is being used to provide multiple single-bit clocks or ATM read and write clock in multislot parallel
backplane applications.
The 1394
–
1995 is an IEEE designation for a high-performance serial bus. This serial bus defines both a
backplane (e.g., GTLP, VME, FB+, CPCI, etc.) physical layer and a point-to-point cable-connected virtual bus.
The backplane version operates at 25, 50, or 100 Mbps, whereas the cable version supports data rates of 100,
200, and 400 Mbps. Both versions are compatible at the link layer and above. The interface standard defines
the transmission method, media in the cable version, and protocol. The primary application of the cable version
is the interconnection of digital A/V equipment and integration of I/O connectivity at the back panel of personal
computers using a low-cost, scalable, high-speed serial interface. The primary application of the backplane
version is to provide a robust control interface to each daughter card. The 1394 standard also provides new
services such as real-time I/O and live connect/disconnect capability for external devices.
electrical
The 1394 standard is a transaction-based packet technology for cable- or backplane-based environments. Both
chassis and peripheral devices can use this technology. The 1394 serial bus is organized as if it were memory
space interconnected between devices, or as if devices resided in slots on the main backplane. Device
addressing is 64 bits wide, partitioned as ten bits for bus ID, six bits for node ID, and 48 bits for memory
addresses. The result is the capability to address up to 1023 buses, with each having up to 63 nodes, each with
281 terabytes of memory. Memory-based addressing, rather than channel addressing, views resources as
registers or memory that can be accessed with processor-to-memory transactions. Each bus entity is termed
a unit, to be individually addressed, reset, and identified. Multiple nodes can physically reside in a single module,
and multiple ports can reside in a single node.
Some key features of the 1394 topology are multimaster capabilities, live connect/disconnect (hot plugging)
capability, genderless cabling connectors on interconnect cabling, and dynamic node address allocation as
nodes are added to the bus. A maximum of 63 nodes can be connected to one network.
The cable-based physical interface uses dc-level line states for signaling during initialization and arbitration.
Both environments use dominant mode addresses for arbitration. The backplane environment does not have
the initialization requirements of the cable environment because it is a physical bus and does not contain
repeaters. Due to the differences, a backplane-to-cable bridge is required to connect these two environments.
The signals transmitted on both the cable and backplane environments are NRZ with data-strobe (DS)
encoding. DS encoding allows only one of the two signal lines to change each data bit-period, essentially
doubling the jitter tolerance with very little additional circuitry overhead in the hardware.
相關PDF資料 |
PDF描述 |
|---|---|
| SN74GTLP1394DR | Bus Exchanger |
| SN74GTLP1394PWR | Bus Exchanger |
| SN74HC4515DW | 4-To-16-Line Demultiplexer |
| CD74HC10H | Triple 3-input NAND Gate |
| CD74HC112NSR96 | FLIP-FLOP|DUAL|J/K TYPE|HC-CMOS|SOP|16PIN|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SN74GTLP1394DR | 功能描述:轉換 - 電壓電平 2bit Bus RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
| SN74GTLP1394DRE4 | 功能描述:轉換 - 電壓電平 2-Bit LVTTL/GTLP Bus Xcvr Adj-Edge-Rate RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
| SN74GTLP1394DRG4 | 功能描述:轉換 - 電壓電平 2B LVTTL to GTLP Adj Edg RateBus Xcvr RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
| SN74GTLP1394PW | 功能描述:轉換 - 電壓電平 2-Bit LVTTL/GTLP Bus Xcvr Adj-Edge-Rate RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
| SN74GTLP1394PWE4 | 功能描述:轉換 - 電壓電平 2-Bit LVTTL/GTLP Bus Xcvr Adj-Edge-Rate RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
發布緊急采購，3分鐘左右您將得到回復。