參數資料
型號： SC802EVB
廠商： Semtech Corporation
英文描述： Fully Integrated Lithium-Ion Battery Charger System with Timer
中文描述： 完全集成的鋰離子電池充電器系統的計時器
文件頁數： 10/16頁
文件大?。?/td> 484K
代理商： SC802EVB
10
2005 Semtech Corp.
www.semtech.com
SC802/SC802A
POWER MANAGEMENT
Prelimi-
nary
Configuring the Output Voltage to the Battery
Fixed Mode
The battery voltage is set by the VPRGM pin in fixed mode
and externally in adjust mode. If VPRGM is logic high the
output voltage is set to 4.2V. If this pin is logic low the
output voltage will be set to 4.1V. For a value other than
4.1V or 4.2V a resistor divider is required.
Adjust Mode
When the SC802 is configured with an output voltage
other than 4.1 or 4.2V it is operating in adjust mode. In
adjust mode the output voltage is set by an external re-
sistor divider. The SC802 provides the ability to discon-
nect the external feedback resistor divider when the
battery is not being charged to reduce current drain from
the battery in normal operation. Connect the external
resistor divider between the VOUT pin and the VPRGM
pin with the divider tap connected to the BSEN pin to
utilize this feature. The SC802 adjust mode schematic is
shown above. The equation for setting the output
voltage is:
3.0
×
R3
R4
1
VOUT
=
The capacitor across R4 in the feedback networks intro-
duces zero-pole frequency compensation for stability.
Place the zero according to the following equation to in-
sure stability.
kHz
100
2
1
C1
R4
×
=
×
π
When the SC802 is in Adjust mode the VCC is required
to be 150mV > Vout. Internal protection circuits will dis-
able the output if VOUT approaches VCC.
t
RT1
THERMISTOR
R8
1K
C1
1uF
R4
R2
R6
C1
R3
R7
1K
ADC Iset
R5
Adjust Mode Schematic
C2
2.2uF
R1
SC802
14
13
1
16
3
7
4
8
6
15
9
12
2
10
11
5
VCC
VCC
BSEN
VOUT
IPRGM
EN/NTC
ITERM
BIPB
GND
VOUT
AFC
RTIM
VPRGM
CHRGB
CPB
RFGND
CHARGER
PRESENT
BATTERY
CHARGE
Capacitor Selection
Input and output capacitors can be low cost ceramic type.
The output capacitance range is 1uF to 4.7uF. The input
capacitor is typically between 0.1uF to 1uF but larger
values will not degrade performance.
Overcurrent and Max Temperature Protection
Overcurrent protection is inherent in all modes of opera-
tion. When the device is in charge-mode (BIPB=low) the
output is current limited to either the pre-charge current
limit value or the fast charge current limit value depend-
ing on the voltage at the output. When the device is in
LDO mode (BIPB=high) the output current is limited to
the fast charge current limit. Max die temperature pro-
tection is included on the SC802. This feature allows
the SC802 to operate with maximum power dissipation
by disabling the output current when the die tempera-
ture reaches OT. The result is that the SC802 will oper-
ate as a pulse charger in extreme power dissipation ap-
plications delivering the maximum allowable output cur-
rent while regulating the internal die temperature to a
safe level.
Remote Kelvin Sensing at the Battery
Kelvin sensing of both the positive and negative termi-
nals of the battery is possible with the SC802. The BSEN
pin provides the positive sensing voltage feedback to
the CV amplifier and should be connected as close to
the battery + terminal as possible. Likewise the REFGND
pin should be kelvin connected to the negative terminal
of the battery. This allows the designer great flexibility in
PCB layout and achieves a much greater accuracy in sens-
ing the battery voltage where it counts, at the battery
terminals! Therefore, when laying out the PCB the de-
signer should route the BSEN pin directly to the terminal
at which the battery gets connected. In the LDO mode,
the BSEN pin will still need to sense the output voltage;
therefore BSEN should never be left floating.
相關PDF資料
PDF描述
SC802IMLTR Fully Integrated Lithium-Ion Battery Charger System with Timer
SC802IMLTRT Fully Integrated Lithium-Ion Battery Charger System with Timer
SC803 Fully Integrated High Current Lithium-Ion Battery Charger System
SC803EVB Fully Integrated High Current Lithium-Ion Battery Charger System
SC803IMLTR Fully Integrated High Current Lithium-Ion Battery Charger System
相關代理商/技術參數
參數描述
SC802IMLTR 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Fully Integrated Lithium-Ion Battery Charger System with Timer
SC802IMLTRT 制造商:Semtech Corporation 功能描述:Controller IC Leaded Process Compatible:
SC802S 功能描述:數據轉換模塊 SC800 8W SERIAL OEM RoHS:否 制造商:Lyrtech 產品:ADC and DAC FMC Modules 轉換速率:250 MSPS, 1 GSPS 信噪比: ADC 輸入端數量:2 DAC 輸出端數量:2 分辨率:14 bit, 16 bit 接口類型:SPI 工作電源電壓:3.3 V, 12 V 工作電源電流: 最大工作溫度: 尺寸:84 mm x 69 mm x 10 mm
SC803 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Fully Integrated High Current Lithium-Ion Battery Charger System
SC8035 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SC8035 是一顆單芯片CMOS 一次性編程語音芯片，使用臺灣最新崁入式EPROM 架構的OTP (One Time Programmable)語音晶元
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*