- 您現在的位置：買賣IC網 > PDF目錄374735 > SC627ULTRT (Semtech Corporation) LED Light Management Unit Charge Pump, 4 LEDs, 700mA Flash LED, Dual LDOs, and SemWireTM Interface PDF資料下載
參數資料
| 型號： | SC627ULTRT |
| 廠商： | Semtech Corporation |
| 英文描述： | LED Light Management Unit Charge Pump, 4 LEDs, 700mA Flash LED, Dual LDOs, and SemWireTM Interface |
| 中文描述： | LED燈管理股電荷泵，4個LED，700mA的閃光LED，雙LDO，和SemWireTM接口 |
| 文件頁數： | 17/23頁 |
| 文件大?。?/td> | 371K |
| 代理商： | SC627ULTRT |
SC627
17
Register Map
Address
D7
D6
D5
D4
D3
D2
D1
D0
Reset
Value
Description
0x00
FADE_1
FADE_0
FADE_EN
BL_4
BL_3
BL_2
BL_1
BL_0
0x00
Backlight
Current
Control
0x01
0
(1)
0
(1)
0
(1)
0
(1)
BLEN_4
BLEN_3
BLEN_2
BLEN_1
0x00
Backlight
Enable Control
0x02
0
(1)
0
(1)
0
(1)
FLTO
FL_2
FL_1
FL_0
FL/SPLB
0x10
Flash/Spotlight
Control
0x03
0
(1)
LDO2_2
LDO2_1
LDO2_0
LDO1_3
LDO1_2
LDO1_1
LDO1_0
0x00
LDO Control
Notes:
(1) 0 = always write a 0 to these bits
Register and Bit Definitions
Backlight Current Control Register (0x00)
This register is used to set the currents for the backlight
current sinks, as well as to enable and set the fade step
rate. These current sinks need to be enabled in the
Backlight Enable Control register to be active.
FADE[1:0]
These bits are used to set the rise/fall rate between two
backlight currents as follows:
FADE_1
FADE_0
Fade Feature
Rise/Fall Rate
(ms/step)
0
0
32
0
1
24
1
0
16
1
1
8
The number of steps in changing the backlight current will
be equal to the change in binary count of bits BL[4:0].
FADE_EN
This bit is used to enable or disable the fade feature. When
the fade function is enabled and a new backlight current
is set, the backlight current will change from its current
value to a new value set by bits BL[4:0] at a rate of 8ms to
32ms per step. A new backlight level cannot be written
during an ongoing fade operation, but an ongoing fade
operation may be cancelled by resetting the fade bit.
Clearing the fade bit during an ongoing fade operation
changes the backlight current immediately to the value
of BL[4:0]. The number of counts to complete a fade
operation equals the difference between the old and new
backlight values to increment or decrement the BL[4:0]
bits. If the fade bit is cleared, the current level will change
immediately without the fade delay. The rate of fade may
be changed dynamically, even while a fade operation is
active, by writing new values to the FADE_1 and FADE_0
bits. The total fade time is determined by the number of
steps between old and new backlight values, multiplied
by the rate of fade in ms/step. The longest elapsed time
for a full scale fade-out of the backlight is nominally 1.024
seconds when the default interval of 32ms is used.
相關PDF資料 |
PDF描述 |
|---|---|
| SC635 | Charge Pump Flash LED Driver |
| SC635EVB | Charge Pump Flash LED Driver |
| SC744110 | Power Solid State Relay |
| SC801 | Fully Integrated High Currnet Lithium-Ion Battery Charger System |
| SC801IMLTR | Fully Integrated High Currnet Lithium-Ion Battery Charger System |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC628 | 功能描述:音頻指示器及警報器 MED CONTINUOUS 6-28V RoHS:否 制造商:PUI Audio 產品:Indicators 聲壓級:85 dB 音調:Continuous 頻率:2300 Hz +/- 300 Hz 電壓額定值:5 VDC 電流額定值:30 mA 端接類型: 直徑:12 mm 安裝:Through Hole |
| SC6-28 | 制造商:WM BERG 功能描述: |
| SC628 | 制造商:Mallory Sonalert Products Inc 功能描述:TRANSDUCER PIEZO 2.9KHZ 80DBA 28VDC |
| SC628-4R | 制造商:Mallory Sonalert Products Inc 功能描述:TRANSDUCER, PIEZO, 2.9KHZ, 80DBA, 28VDC; Transducer Function:Alarm; Tones:Continuous; Supply Voltage Min:6V; Supply Voltage Max:28V; Operating Current Max:18mA; Sound Level SPL:80dBA; Resonant Frequency:2.9kHz; External Height:32.6mm;RoHS Compliant: Yes |
| SC628A | 功能描述:音頻指示器及警報器 MED CONTINUOUS 6-28V RoHS:否 制造商:PUI Audio 產品:Indicators 聲壓級:85 dB 音調:Continuous 頻率:2300 Hz +/- 300 Hz 電壓額定值:5 VDC 電流額定值:30 mA 端接類型: 直徑:12 mm 安裝:Through Hole |
發布緊急采購，3分鐘左右您將得到回復。