- 您現在的位置：買賣IC網 > PDF目錄374734 > SC617 (Semtech Corporation) Charge Pump Flash LED Driver with Safety Timer PDF資料下載
參數資料
| 型號： | SC617 |
| 廠商： | Semtech Corporation |
| 英文描述： | Charge Pump Flash LED Driver with Safety Timer |
| 中文描述： | 充電泵閃光LED驅動器的安全定時器 |
| 文件頁數： | 11/13頁 |
| 文件大?。?/td> | 219K |
| 代理商： | SC617 |
SC617
11
PCB Layout Considerations
The following layout is suggested for a two-layer design.
The capacitors C1 and C2 are the bucket capacitors and
each conducts the full load current of up to 500mA pulsed
for one half clock cycle. C3 is the output decoupling
capacitor placed near the VOUT pin. C4 is the input
decoupling capacitor placed near the VIN pin. Multiple
vias should be used whenever it is necessary to change
layers on nets connecting to pins VIN, VOUT, GND, C1-,
C1+, C2- and C2+.
The load current return path is from the ISET sense point
through the resistor and back to the ground pins.
Resistance in this path adds to the total resistance and
has the effect of reducing the LED current by about 4%
per 10mV of DC drop across the return copper trace in
flash mode. For this reason, it is crucial to have a low resis-
tance return path. Place and ground the resistor as close
as possible to the ground pin of the SC617. The trace from
the ISET pin has virtually no current. The ISET trace should
make contact at the pad of the power sense resistor to
minimize the effect of voltage drop between the LED
cathode and the resistor.
Resistor R1 is routed with a very low resistance connec-
tion between R1 and GND pin 3. The sense trace between
Pin 6 and R1 is routed around the ground vias, allowing
the shortest ground return path possible. The sense trace
is connected to R1 at the positive terminal pad for the
most accurate output possible. The bottom copper layer
is mostly a ground plane with no obstructions between
the ground vias. The smaller rectangle to the left con-
nects the input power to VIN pin 1 and input capacitor
C4. The two traces at the lower left are for logic inputs
FLASH and CTRL. The trace to the right is the ISET pin
sense trace. The sense trace is routed out of the path of
the returning ground current.
Thermal Resistance Considerations
The SC617 package is thermally efficient when the circuit
board layout connects the thermal pad through multiple
vias to the ground plane. The thermal resistance is rated
at 40°C/W, and this rating is dependent on the connec-
tion between the thermal pad and the ground plane. The
layout should keep the junction temperature below the
OTP limit while operating the SC617 within the specified
electrical conditions for I
OUT
and V
ISET
. A poor layout may
allow the junction temperature to reach the OTP limit
Applications Information (continued)
while in flash or spotlight mode. It is critical to maintain
adequate ground plane around the device to maximize
heat transfer and avoid over-temperature shutdown.
相關PDF資料 |
PDF描述 |
|---|---|
| SC617EVB | Charge Pump Flash LED Driver with Safety Timer |
| SC617ULTRT | Charge Pump Flash LED Driver with Safety Timer |
| SC618 | Charge Pump Flash LED Driver with Safety Timer |
| SC618EVB | Charge Pump Flash LED Driver with Safety Timer |
| SC618ULTRT | Charge Pump Flash LED Driver with Safety Timer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC617EVB | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Charge Pump Flash LED Driver with Safety Timer |
| SC617ULTRT | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Charge Pump Flash LED Driver with Safety Timer |
| SC618 | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Charge Pump Flash LED Driver with Safety Timer |
| SC618_08 | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Charge Pump Flash LED Driver with Safety Timer |
| SC618EVB | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Charge Pump Flash LED Driver with Safety Timer |
發布緊急采購，3分鐘左右您將得到回復。