參數資料
型號： SC480
廠商： Semtech Corporation
英文描述： Complete DDR1/2/3 Memory Power Supply
中文描述： 完全DDR1/2/3內存供電
文件頁數： 14/25頁
文件大?。?/td> 858K
代理商： SC480
14
2006 Semtech Corp.
www.semtech.com
POWER MANAGEMENT
Application Information (Cont.)
Dropout Performance
The output voltage adjust range for continuous-conduction
operation is limited by the
fi
xed 400nS (typical) Minimum
Off-time One-shot. For best dropout performance, use the
slowest on-time setting of 200KHz. When working with
low input voltages, the duty-factor limit must be calculated
using worst-case values for on and off times. The IC duty-
factor limitation is given by:
SC480
(MAX)
TOFF
(MIN)
TON
(MIN)
TON
DUTY
Be sure to include inductor resistance and MOSFET on-
state voltage drops when performing worst-case dropout
duty-factor calculations.
SC480 System DC Accuracy (VDDQ Controller)
Three IC parameters affect VDDQ accuracy: the internal
1.5V reference, the error comparator offset voltage, and
the switching frequency variation with line and load.
The internal 1%, 1.5V reference contains two error
components, a 0.5% DC error and a 0.5% supply and
temperature error. The error comparator offset is trimmed
so that it trips when the feedback pin is nominally 1.5
volts +/-1% at room temperature. The comparator offset
trim compensates for any DC error in the reference. Thus,
the percentage error is the sum of the reference variation
over supply and temperature and the offset in the error
comparator, or 1.5% total.
The on-time pulse in the SC480 is calculated to give a
pseudo-
fi
xed frequency. Nevertheless, some frequency
variation with line and load can be expected. This variation
changes the output ripple voltage. Because constant on-
time converters regulate to the valley of the output ripple,
of the output ripple appears as a DC regulation error.
For example, If the output ripple is 50mV with VIN = 6
volts, then the measured DC output will be 25mV above
the comparator trip point. If the ripple increases to 80mV
with VIN = 25 volts, then the measured DC output will
be 40mV above the comparator trip. The best way to
minimize this effect is to minimize the output ripple.
To compensate for valley regulation it is often desirable
to use passive droop. Take the feedback directly from the
output side of the inductor, incorporating a small amount
of trace resistance between the inductor and output
capacitor. This trace resistance should be optimized
so that at full load the output droops to near the lower
regulation limit. Passive droop minimizes the required
output capacitance because the voltage excursions due
to load steps are reduced.
Board components and layout also in
fl
uence DC accuracy.
The use of 1% feedback resistors contributes up to 1%
error. If tighter DC accuracy is required use 0.1% feedback
resistors.
The output inductor value may change with current. This
will change the output ripple and thus the DC output
voltage (it will not change the frequency).
Switching frequency variation with load can be minimized
by choosing lower RDS
MOSFETs. High RDS
MOSFETS
will cause the switching frequency to increase as the load
current increases. This will reduce the ripple and thus
the DC output voltage. This inherent droop should be
considered when deciding if passive droop is required, or
if passive droop is desired in order to further reduce the
output capacitance.
Output DC Accuracy (VTT Output)
The VTT accuracy compared to VDDQ is determined by
two parameters: the REF output accuracy, and the VTT
output accuracy with respect to REF. The REF output
is generated internally from the VDDQS (sense input),
and tracks VDDQS with 2% accuracy. This REF output
becomes the reference for the VTT regulator. The VTT
regulator then tracks REF within +/-40mV (typically zero).
The total VTT/VDDQ tracking accuracy is then:
40mV
0.02
2
VDDQS
error
VTT
r
r
x
DDR Reference Buffer
The reference buffer is capable of sourcing 10mA. The
reference buffer has a class A output stage and therefore
will not sink signi
fi
cant current; there is an internal 50 k
Ω
(typical) pulldown to ground. If higher current sinking is
required, an external pulldown resistor should be added.
Make sure that the ground side of this pulldown is tied to
the VTT ground plane near the PGND2 pin.
相關PDF資料
PDF描述
SC480EVB Complete DDR1/2/3 Memory Power Supply
SC480IMLTRT Complete DDR1/2/3 Memory Power Supply
SC4810B High Performance Current Mode PWM Controller with Complementary Output, Programmable Delay
SC4810BIMLTRT High Performance Current Mode PWM Controller with Complementary Output, Programmable Delay
SC4810BITSTRT High Performance Current Mode PWM Controller with Complementary Output, Programmable Delay
相關代理商/技術參數
參數描述
SC4806 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Multiple Function Double Ended PWM Controller
SC4806MLTRT 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Multiple Function Double Ended PWM Controller
SC4808A 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:High Performance Dual Ended PWM Controller
SC4808AIMSTR 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:High Performance Dual Ended PWM Controller
SC4808AIMSTRT 制造商:Semtech Corporation 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*