參數資料
型號： SC16C850IET,115
廠商： NXP Semiconductors
文件頁數： 53/55頁
文件大小： 0K
描述： IC UART SINGLE W/FIFO 36-TFBGA
標準包裝： 1,000
特點： 可編程
通道數： 1，UART
FIFO's： 128 字節
規程： RS485
電源電壓： 2.5 V ~ 3.3 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 36-TFBGA
供應商設備封裝： 36-TFBGA（3.5x3.5）
包裝： 帶卷 (TR)
其它名稱： 935284685115
SC16C850IET-G
SC16C850IET-G-ND
SC16C850
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 11 November 2010
7 of 55
NXP Semiconductors
SC16C850
2.5 to 3.3 V UART with 128-byte FIFOs and IrDA encoder/decoder
D0
F4
29
I/O
Data bus (bidirectional). These pins are the 8-bit, 3-state data bus for
transferring information to or from the controlling CPU. D0 is the least
significant bit and the first data bit in a transmit or receive serial data stream.
D1
E4
30
I/O
D2
F5
31
I/O
D3
E5
32
I/O
D4
F6
1
I/O
D5
E6
3
I/O
D6
4
I/O
D7
D5
5
I/O
INT
(IRQ)
-
20
O
When 16/68 pin is at logic 1 or unconnected, this output becomes active HIGH
interrupt output. The output state is defined by the user through the software
setting of MCR[5]. INT is set to the active mode when MCR[5] is set to a
logic 1. INT is set to the open-source mode when MCR[5] is set to a logic 0.
When 16/68 pin is at logic 0, this output becomes device interrupt output
(active LOW, open-drain). An external pull-up resistor to VDD is required.
INT
D1
-
O
Interrupt output (active HIGH). The output state is defined by the user
through the software setting of MCR[5]. INT is set to the active mode when
MCR[5] is set to a logic 1. INT is set to the open-source mode when MCR[5] is
set to a logic 0.
IOR
(VDD)
-14
I
When 16/68 pin is at logic 1, this input becomes the read strobe (active LOW).
When 16/68 pin is at logic 0, this input pin is not used and should be
connected to VDD.
IOR
A3
-
I
Read strobe (active LOW).
IOW
(R/W)
-
12
I
When 16/68 pin is at logic 1 or unconnected, this input becomes the write
strobe (active LOW).
When 16/68 pin is at logic 0, this input becomes read strobe when it is at logic
HIGH, and write strobe when it is at logic LOW.
IOW
B4
-
I
Write strobe (active LOW).
LOWPWR
B5
9
I
Low Power. When asserted (active HIGH), the device immediately goes into
low power mode. The oscillator is shut-off and some host interface pins are
isolated from the host’s bus to reduce power consumption. The device only
returns to normal mode when the LOWPWR pin is de-asserted. On the
negative edge of a de-asserting LOWPWR signal, the device is automatically
reset and all registers return to their default reset states. This pin has a 22 k
Ω
internal pull-down resistor, therefore, it can be left unconnected (refer to
RESET
(RESET)
-23
I
Master Reset. When 16/68 pin is at logic 1 or unconnected, this input
becomes the RESET pin (active HIGH).
When 16/68 pin is at logic LOW, this input pin becomes RESET (active LOW).
initialization details.)
RESET
F1
-
I
Reset input (active HIGH). See Section 7.23 “SC16C850 external reset
condition and software reset” for initialization details.
RI
F3
27
I
Ring Indicator (active LOW). A logic 0 on this pin indicates the modem has
received a ringing signal from the telephone line. A logic 1 transition on this
input pin will generate an interrupt if modem status interrupt is enabled. Status
can be tested by reading MCR[6].
Table 2.
Pin description …continued
Symbol
Pin
Type
Description
TFBGA36
HVQFN32
相關PDF資料
PDF描述
MS27508E12B22SC CONN RCPT 22POS BOX MNT W/SCKT
MS27484P12B35S CONN PLUG 22POS STRAIGHT W/SCKT
MS27474P12B98P CONN RCPT 10POS JAM NUT W/PINS
D38999/24WD15PN CONN RCPT 15POS JAM NUT W/PINS
MS3116F-14-19S CONN PLUG 19POS W/SOCKET SOLDER
相關代理商/技術參數
參數描述
SC16C850IET-G 功能描述:UART 接口集成電路 16C 2.5-5V 5MBPS UART 128BFIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C850IET-S 功能描述:UART 接口集成電路 16C 2.5-5V 5MBPS UART 128BFIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C850L 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1.8 V single UART, 5 Mbit/s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode parallel bus interface
SC16C850LIB,128 制造商:NXP Semiconductors 功能描述:
SC16C850LIB,151 制造商:NXP Semiconductors 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*