參數資料
型號： SC16C550
廠商： NXP Semiconductors N.V.
英文描述： Universal Asynchronous Receiver/Transmitter (UART) with 16-byte FIFO and infrared (IrDA) encoder/decoder
中文描述： 通用異步接收器/發送器（UART），16字節FIFO和紅外線（IrDA）編碼器/解碼器
文件頁數： 7/52頁
文件大?。?/td> 639K
代理商： SC16C550
Philips Semiconductors
SC16C550
UART with 16-byte FIFO and IrDA encoder/decoder
Product data
Rev. 05 — 19 June 2003
7 of 52
9397 750 11619
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
CS0, CS1,
CS2
14, 15,
16
9, 10,
11
12,13,
14
I
Chip select.
When CS0 and CS1 are HIGH and CS2 is LOW, these
three inputs select the UART. When any of these inputs are inactive,
the UART remains inactive (refer to AS description).
Clear to send.
CTS is a modem status signal. Its condition can be
checked by reading bit 4 (CTS) of the modem status register. Bit 0
(CTS) of the modem status register indicates that CTS has changed
states since the last read from the modem status register. If the
modem status interrupt is enabled when CTS changes levels and the
auto-CTS mode is not enabled, an interrupt is generated. CTS is also
used in the auto-CTS mode to control the transmitter.
Data bus.
Eight data lines with 3-State outputs provide a bi-directional
path for data, control and status information between the UART and
the CPU.
Data carrier detect.
DCD is a modem status signal. Its condition can
be checked by reading bit 7 (DCD) of the modem status register. Bit 3
(DCD) of the modem status register indicates that DCD has changed
states since the last read from the modem status register. If the
modem status interrupt is enabled when DCD changes levels, an
interrupt is generated.
Driver disable.
DDIS is active (LOW) when the CPU is not reading
data. When active, DDIS can disable an external transceiver.
Data set ready.
DSR is a modem status signal. Its condition can be
checked by reading bit 5 (DSR) of the modem status register. Bit 1
(DSR) of the modem status register indicates DSR has changed levels
since the last read from the modem status register. If the modem
status interrupt is enabled when DSR changes levels, an interrupt is
generated.
Data terminal ready.
When active (LOW), DTR informs a modem or
data set that the UART is ready to establish communication. DTR is
placed in the active level by setting the DTR bit of the modem control
register. DTR is placed in the inactive level either as a result of a
Master Reset, during loop mode operation, or clearing the DTR bit.
Interrupt.
When active (HIGH), INT informs the CPU that the UART
has an interrupt to be serviced. Four conditions that cause an interrupt
to be issued are: a receiver error, received data that is available or
timed out (FIFO mode only), an empty transmitter holding register or
an enabled modem status interrupt. INT is reset (deactivated) either
when the interrupt is serviced or as a result of a Master Reset.
Master Reset.
When active (HIGH), MR clears most UART registers
and sets the levels of various output signals.
Not connected.
CTS
40
38
36
I
D7-D0
2-9
43-47,
2-4
8-1
I/O
DCD
42
40
38
I
DDIS
26
22
23
O
DSR
41
39
37
I
DTR
37
33
33
O
INT
33
30
30
O
MR
39
35
35
I
NC
1, 12,
23, 34
1, 5, 13,
21, 25,
36, 37,
48
34, 31
-
-
OUT1, OUT2 38, 35
34, 31
O
Outputs 1 and 2.
These are user-designated output terminals that are
set to the active (low) level by setting respective modem control
register (MCR) bits (OUT1 and OUT2). OUT1 and OUT2 are set to
inactive the (HIGH) level as a result of Master Reset, during loop mode
operations, or by clearing bit 2 (OUT1) or bit 3 (OUT2) of the MCR.
Table 2:
Symbol
Pin description
…continued
Pin
PLCC44 LQFP48 DIP40
Type
Description
相關PDF資料
PDF描述
SC16C550IA44 Universal Asynchronous Receiver/Transmitter (UART) with 16-byte FIFO and infrared (IrDA) encoder/decoder
SC16C550IB48 Universal Asynchronous Receiver/Transmitter (UART) with 16-byte FIFO and infrared (IrDA) encoder/decoder
SC16C554IB64 Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder
SC16C554 Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder
SC16C554DB 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs
相關代理商/技術參數
參數描述
SC16C550B 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5 V, 3.3 V and 2.5 V UART with 16-byte FIFOs
SC16C550BIA44 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C550BIA44,512 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C550BIA44,518 功能描述:UART 接口集成電路 1CH. UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C550BIA44,529 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*