- 您現在的位置：買賣IC網 > PDF目錄372121 > SC16C550 (NXP Semiconductors N.V.) Universal Asynchronous Receiver/Transmitter (UART) with 16-byte FIFO and infrared (IrDA) encoder/decoder PDF資料下載
參數資料
| 型號： | SC16C550 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Universal Asynchronous Receiver/Transmitter (UART) with 16-byte FIFO and infrared (IrDA) encoder/decoder |
| 中文描述： | 通用異步接收器/發送器（UART），16字節FIFO和紅外線（IrDA）編碼器/解碼器 |
| 文件頁數： | 14/52頁 |
| 文件大?。?/td> | 639K |
| 代理商： | SC16C550 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
Philips Semiconductors
SC16C550
UART with 16-byte FIFO and IrDA encoder/decoder
Product data
Rev. 05 — 19 June 2003
14 of 52
9397 750 11619
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
6.5 Special feature software flow control
A special feature is provided to detect an 8-bit character when EFR[5] is set. When
8-bit character is detected, it will be placed on the user-accessible data stack along
with normal incoming RX data. This condition is selected in conjunction with
EFR[0-3]. Note that software flow control should be turned off when using this special
mode by setting EFR[0-3] to a logic 0.
The SC16C550 compares each incoming receive character with Xoff2 data. If a
match exists, the received data will be transferred to the FIFO, and ISR[4] will be set
to indicate detection of a special character. Although
Table 8 “SC16C550 internal
registers”
shows each X-Register with eight bits of character information, the actual
number of bits is dependent on the programmed word length. Line Control Register
bits LCR[0-1] define the number of character bits, i.e., either 5 bits, 6 bits, 7 bits or
8 bits. The word length selected by LCR[0-1] also determine the number of bits that
will be used for the special character comparison. Bit 0 in the X-registers corresponds
with the LSB bit for the receive character.
6.6 Hardware/software and time-out interrupts
Three special interrupts have been added to monitor the hardware and software flow
control. The interrupts are enabled by IER[5-7]. Care must be taken when handling
these interrupts. Following a reset, the transmitter interrupt is enabled, the SC16C550
will issue an interrupt to indicate that the Transmit Holding Register is empty. This
interrupt must be serviced prior to continuing operations. The LSR register provides
the current singular highest priority interrupt only. It could be noted that CTS and RTS
interrupts have lowest interrupt priority. A condition can exist where a higher priority
interrupt may mask the lower priority CTS/RTS interrupt(s). Only after servicing the
higher pending interrupt will the lower priority CTS/TRS interrupt(s) be reflected in the
status register. Servicing the interrupt without investigating further interrupt conditions
can result in data errors.
When two interrupt conditions have the same priority, it is important to service these
interrupts correctly. Receive Data Ready and Receive Time Out have the same
interrupt priority (when enabled by IER[3]). The receiver issues an interrupt after the
number of characters have reached the programmed trigger level. In this case, the
SC16C550 FIFO may hold more characters than the programmed trigger level.
Following the removal of a data byte, the user should re-check LSR[0] for additional
characters. A Receive Time Out will not occur if the receive FIFO is empty. The
time-out counter is reset at the center of each stop bit received or each time the
receive holding register (RHR) is read. The actual time-out value is 4 character time,
including data information length, start bit, parity bit, and the size of stop bit, i.e., 1
×
,
1.5
×
, or 2
×
bit times.
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C550IA44 | Universal Asynchronous Receiver/Transmitter (UART) with 16-byte FIFO and infrared (IrDA) encoder/decoder |
| SC16C550IB48 | Universal Asynchronous Receiver/Transmitter (UART) with 16-byte FIFO and infrared (IrDA) encoder/decoder |
| SC16C554IB64 | Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder |
| SC16C554 | Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder |
| SC16C554DB | 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C550B | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5 V, 3.3 V and 2.5 V UART with 16-byte FIFOs |
| SC16C550BIA44 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C550BIA44,512 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C550BIA44,518 | 功能描述:UART 接口集成電路 1CH. UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C550BIA44,529 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。