參數資料
型號： SAK-XC888CLM-8FFA
廠商： INFINEON TECHNOLOGIES AG
元件分類： 8位微控制器
英文描述： 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
中文描述： 8位微控制器與2/4/8K字節在系統可編程閃存
文件頁數： 94/119頁
文件大小： 895K
代理商： SAK-XC888CLM-8FFA
XC886/888CLM
Functional Description
Data Sheet
Prelimary
90
V0.1, 2006-02
3.19
On-Chip Debug Support
The On-Chip Debug Support (OCDS) provides the basic functionality required for the
software development and debugging of XC800-based systems.
The OCDS design is based on these principles:
use the built-in debug functionality of the XC800 Core
add a minimum of hardware overhead
provide support for most of the operations by a Monitor Program
use standard interfaces to communicate with the Host (a Debugger)
Features:
Set breakpoints on instruction address and on address range within the Program
Memory
Set breakpoints on internal RAM address range
Support unlimited software breakpoints in Flash/RAM code region
Process external breaks via JTAG and upon activating a dedicated pin
Step through the program code
The OCDS functional blocks are shown in
Figure 37
. The Monitor Mode Control (MMC)
block at the center of OCDS system brings together control signals and supports the
overall functionality. The MMC communicates with the XC800 Core, primarily via the
Debug Interface, and also receives reset and clock signals.
After processing memory address and control signals from the core, the MMC provides
proper access to the dedicated extra-memories: a Monitor ROM (holding the code) and
a Monitor RAM (for work-data and Monitor-stack).
The OCDS system is accessed through the JTAG
1)
, which is an interface dedicated
exclusively for testing and debugging activities and is not normally used in an
application. The dedicated MBC pin is used for external configuration and debugging
control.
Note: All the debug functionality described here can normally be used only after XC886/
888 has been started in OCDS mode.
1)
The pins of the JTAG port can be assigned to either the primary port (Port 0) or either of the secondary ports
(Ports 1 and 2/Port 5).
User must set the JTAG pins (TCK and TDI) as input during connection with the OCDS system.
相關PDF資料
PDF描述
SAK-XC888CM-6FFA 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
SAK-XC888CM-8FFA 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
SAK-XC888LM-6FFA 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
SAK-XC888LM-8FFA 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
SAF1032 REMOTE CONTROL SYSTEM FOR INFRARED OPERATION
相關代理商/技術參數
參數描述
SAK-XC888CLM-8FFA 5V AC 功能描述:8位微控制器 -MCU MICROCONTROLLER 8-BIT RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
SAK-XC888CLM-8FFA 5V ACTR 制造商:Infineon Technologies AG 功能描述:
SAKXC888CLM8FFA5VAC 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
SAKXC888CLM8FFAT 制造商:Infineon Technologies AG 功能描述:MCU 8-Bit XC800 8051 CISC 32KB Flash 2.5V/3.3V/5V 64-Pin TQFP
SAK-XC888CM-6FFA 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit Single-Chip Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*