參數資料
型號: SAK-XC2232N-24F40L
廠商: INFINEON TECHNOLOGIES AG
元件分類: 微控制器/微處理器
英文描述: 16-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP64
封裝: 0.50 MM PITCH, GREEN, PLASTIC, LQFP-64
文件頁數: 60/110頁
文件大?。?/td> 1601K
代理商: SAK-XC2232N-24F40L
XC2232N, XC2234N, XC2236N, XC2238N
XC2000 Family / Value Line
Functional Description
Data Sheet
53
V1.3, 2010-04
MultiCAN Features
CAN functionality conforming to CAN specification V2.0 B active for each CAN node
(compliant to ISO 11898)
Independent CAN nodes
Set of independent message objects (shared by the CAN nodes)
Dedicated control registers for each CAN node
Data transfer rate up to 1 Mbit/s, individually programmable for each node
Flexible and powerful message transfer control and error handling capabilities
Full-CAN functionality for message objects:
– Can be assigned to one of the CAN nodes
– Configurable as transmit or receive objects, or as message buffer FIFO
– Handle 11-bit or 29-bit identifiers with programmable acceptance mask for filtering
– Remote Monitoring Mode, and frame counter for monitoring
Automatic Gateway Mode support
16 individually programmable interrupt nodes
Analyzer mode for CAN bus monitoring
3.14
System Timer
The System Timer consists of a programmable prescaler and two concatenated timers
(10 bits and 6 bits). Both timers can generate interrupt requests. The clock source can
be selected and the timers can also run during power reduction modes.
Therefore, the System Timer enables the software to maintain the current time for
scheduling functions or for the implementation of a clock.
3.15
Watchdog Timer
The Watchdog Timer is one of the fail-safe mechanisms which have been implemented
to prevent the controller from malfunctioning for longer periods of time.
The Watchdog Timer is always enabled after an application reset of the chip. It can be
disabled and enabled at any time by executing the instructions DISWDT and ENWDT
respectively. The software has to service the Watchdog Timer before it overflows. If this
is not the case because of a hardware or software failure, the Watchdog Timer
overflows, generating a prewarning interrupt and then a reset request.
The Watchdog Timer is a 16-bit timer clocked with the system clock divided by 16,384
or 256. The Watchdog Timer register is set to a prespecified reload value (stored in
WDTREL) in order to allow further variation of the monitored time interval. Each time it
is serviced by the application software, the Watchdog Timer is reloaded and the
prescaler is cleared.
Time intervals between 3.2
μs and 13.4 s can be monitored (@ 80 MHz).
The default Watchdog Timer interval after power-up is 6.5 ms (@ 10 MHz).
相關PDF資料
PDF描述
SST89E51RC-40-C-NJE 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQCC44
SST89V54RD2A-33-I-NJE 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQCC44
S80C32E-25R 8-BIT, 25 MHz, MICROCONTROLLER, PQCC44
S80C52EXXX-16D 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQCC44
SST89V52RC-33-I-NJ 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQCC44
相關代理商/技術參數
參數描述
SAK-XC2232N-40F80LAA 制造商:Infineon Technologies AG 功能描述:
SAK-XC2234L-20F66L AA 功能描述:16位微控制器 - MCU 16/32b Sngl Chip MCU 32Bit Perform 66MHz RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
SAK-XC2236N-16F66LAA 制造商:Infineon Technologies AG 功能描述:
SAK-XC2236N-24F40L 功能描述:16位微控制器 - MCU 16 BIT FLASH RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
SAK-XC2236N-24F40L AA 功能描述:16位微控制器 - MCU 16-Bit Single-Chip MCU w/32 Bit Perform RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT