參數資料
型號： SAA7826HL
廠商： NXP Semiconductors N.V.
元件分類： DRAM
英文描述： CD audio decoder, digital servo and filterless DAC with integrated pre-amp and laser control
封裝： SAA7826HL/M1AS/S5<SOT315-1 (LQFP80)|<<http://www.nxp.com/packages/SOT315-1.html<1<Always Pb-free,;
文件頁數： 34/89頁
文件大?。?/td> 379K
代理商： SAA7826HL
2003 Oct 01
34
Philips Semiconductors
Product specification
CD audio decoder, digital servo and filterless
DAC with integrated pre-amp and laser control
SAA7826
handbook, full pagewidth
DECIMATION
FILTER
FAST
FILTER
DEFECT
GENERATION
PROGRAMMABLE
HOLD-OFF
SLOW
FILTER
defect
output
sat1
sat2
+
MBG421
Fig.22 Block diagram of the defect detector.
7.16.9
H
IGH
-
LEVEL FEATURES
7.16.9.1
Interrupt mechanism and STATUS pin
The STATUS pin is an output which can be configured by
decoder register 7 and new shadow register C(bank 3) for
one of three different modes of operation. These are:
Output the interrupt signal generated by the servo part
(it should be noted that the selection of this mode will
override all other modes)
Output the decoder status bit (active LOW) selected by
decoder register 2 (only available in 4-wire bus mode)
Output DC offset information (it should be noted that this
mode is used in conjunction with the decoder status
mode; see Section 7.5).
Eight signals from the interrupt status register are
selectable from the servo part via the interrupt_mask
parameter. The interrupt is reset by sending the read
high-level status command. The 8 signals are as follows:
Focus lost: dropout of longer than 3 ms
Subcode ready
Subcode absolute seconds changed
Subcode discontinuity detected: new subcode time
before previous subcode time, or more than 10 frames
later than previous subcode time
Radial error: during radial on-track, no new subcode
frame occurs within the time defined by the
‘playwatchtime’ parameter; during radial jump, less than
4 tracks have been crossed during the time defined by
the ‘jumpwatchtime’ parameter
Autosequencer state change
Autosequencer error
Subcode interface blocked: the internal decoder
interface is being used.
It should be noted that if the STATUS pin is configured to
output decoder status information [decoder register
7 = XX10 and new shadow register C (bank 3) = X00X]
and either the microcontroller writes a different value to
decoderregister 2orthedecoderinterfaceisenabledthen
the STATUS output will change.
7.16.9.2
Decoder interface
The decoder interface allows decoder and shadow
registers to be programmed and subcode Q-channel data
to be read via servo commands. The interface is enabled
or disabled by the preset latch command (and the
xtra_preset parameter).
7.16.9.3
Automatic error handling
Three Watchdogs are present:
Focus: detects focus dropout of longer than 3 ms, sets
focus lost interrupt, switches off radial and sledge
servos and disables the drive-to-disc motor
Radial play: started when radial servo is in on-track
mode and a first subcode frame is found; detects when
the maximum time between two subcode frames
exceeds the time set by the playwatchtime parameter; it
then sets the radial error interrupt, switches radial and
sledge servos off and puts the disc motor into jump
mode
Radial jump: active when radial servo is in long jump or
short jump modes; detects when the off-track counter
value decreases by less than 4 tracks between two
readings (the time interval is set by the jumpwatchtime
parameter); it then sets the radial jump error, switches
radial and sledge servos off to cancel jump.
The focus Watchdog is always active, the radial
Watchdogs are selectable via the radcontrol parameter.
相關PDF資料
PDF描述
SAA7893 Super audio media player
SAA7893HL Super audio media player
SAA8112HL Digital Camera Signal Processor and Microcontroller(數字照相信號處理器和微控制器)
SAA8113HL Digital PC-camera signal processor(數字PC照相信號處理器)
SAA8115HL Digital Camera USB Interface(數字照相USB接口)
相關代理商/技術參數
參數描述
SAA7826HL/E/M1A 功能描述:音頻數/模轉換器 IC PHONIC AUTO RoHS:否 制造商:Texas Instruments 轉換器數量: 分辨率:16 bit 接口類型:I2S, UBS 轉換速率: 信噪比:98 dB 工作電源電壓:5 V DAC 輸出端數量:2 工作溫度范圍:- 25 C to + 85 C 電源電流:23 mA 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-32 封裝:Reel
SAA7826HL/E/M1A,55 功能描述:音頻數/模轉換器 IC PHONIC AUTO RoHS:否 制造商:Texas Instruments 轉換器數量: 分辨率:16 bit 接口類型:I2S, UBS 轉換速率: 信噪比:98 dB 工作電源電壓:5 V DAC 輸出端數量:2 工作溫度范圍:- 25 C to + 85 C 電源電流:23 mA 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-32 封裝:Reel
SAA7826HL/M1A 功能描述:音頻數/模轉換器 IC PHONIC AUTO RoHS:否 制造商:Texas Instruments 轉換器數量: 分辨率:16 bit 接口類型:I2S, UBS 轉換速率: 信噪比:98 dB 工作電源電壓:5 V DAC 輸出端數量:2 工作溫度范圍:- 25 C to + 85 C 電源電流:23 mA 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-32 封裝:Reel
SAA7826HL/M1A,557 功能描述:音頻數/模轉換器 IC PHONIC AUTO RoHS:否 制造商:Texas Instruments 轉換器數量: 分辨率:16 bit 接口類型:I2S, UBS 轉換速率: 信噪比:98 dB 工作電源電壓:5 V DAC 輸出端數量:2 工作溫度范圍:- 25 C to + 85 C 電源電流:23 mA 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-32 封裝:Reel
SAA7826HL/M1AS/S5, 制造商:NXP Semiconductors 功能描述:- Tape and Reel 制造商:NXP Semiconductors 功能描述:DSP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*