- 您現在的位置：買賣IC網 > PDF目錄359286 > S29GL128P90FAI010 (SPANSION LLC) 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology PDF資料下載
參數資料
| 型號： | S29GL128P90FAI010 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology |
| 中文描述： | 128M X 1 FLASH 3V PROM, 90 ns, PBGA64 |
| 封裝： | 13 X 11 MM, 1 MM PITCH, FBGA-64 |
| 文件頁數： | 43/77頁 |
| 文件大?。?/td> | 2121K |
| 代理商： | S29GL128P90FAI010 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁
November 8, 2007 S29GL-P_00_A7
S29GL-P MirrorBit
Flash Family
43
D a t a
S h e e t
( P r e l i m i n a r y )
8.1
Lock Register
As shipped from the factory, all devices default to the persistent mode when power is applied, and all sectors
are unprotected, unless otherwise chosen through the DYB ordering option (see
Ordering Information
on page 9
). The device programmer or host system must then choose which sector protection method to use.
Programming (setting to “0”) any one of the following two one-time programmable, non-volatile bits locks the
part permanently in that mode:
Lock Register Persistent Protection Mode Lock Bit (DQ1)
Lock Register Password Protection Mode Lock Bit (DQ2)
For programming lock register bits refer to
Table 12.2 on page 69
and
Table 12.4 on page 71
.
Notes
1. If the password mode is chosen, the password must be programmed before setting the
corresponding lock register bit.
2. After the Lock Register Bits Command Set Entry command sequence is written, reads and writes
for Sector 0 are disabled, while reads from other sectors are allowed until exiting this mode.
3. If both lock bits are selected to be programmed (to zeros) at the same time, the operation aborts.
4. Once the Password Mode Lock Bit is programmed, the Persistent Mode Lock Bit is permanently
disabled, and no changes to the protection scheme are allowed. Similarly, if the Persistent Mode
Lock Bit is programmed, the Password Mode is permanently disabled.
After selecting a sector protection method, each sector can operate in any of the following three states:
1.
Constantly locked.
The selected sectors are protected and can not be reprogrammed unless PPB
lock bit is cleared via a password, hardware reset, or power cycle.
2.
Dynamically locked.
The selected sectors are protected and can be altered via software
commands.
3.
Unlocked.
The sectors are unprotected and can be erased and/or programmed.
These states are controlled by the bit types described in
Section 8.2
–
Section 8.5
.
8.2
Persistent Protection Bits
The Persistent Protection Bits are unique and nonvolatile for each sector and have the same endurances as
the Flash memory. Preprogramming and verification prior to erasure are handled by the device, and therefore
do not require system monitoring.
Notes
1. Each PPB is individually programmed and all are erased in parallel.
2. While programming PPB for a sector, array data can be read from any other sector, except Sector
0 (used for Data# Polling) and the sector in which sector PPB is being programmed.
3. Entry command disables reads and writes for the sector selected.
4. Reads within that sector return the PPB status for that sector.
5. All Reads must be performed using the read mode.
6. The specific sector address (A25-A16 GL01GP, A24-A16 GL512P, A23-A16 GL256P, A22-A16
GL128P) are written at the same time as the program command.
7. If the PPB Lock Bit is set, the PPB Program or erase command does not execute and times-out
without programming or erasing the PPB.
Table 8.1
Lock Register
DQ15-3
DQ2
DQ1
DQ0
Don’t Care
Password Protection Mode
Lock Bit
Persistent Protection Mode
Lock Bit
Secured Silicon Sector
Protection Bit
相關PDF資料 |
PDF描述 |
|---|---|
| S3901-1024Q | NMOS Linear image sensor |
| S3901-512F | NMOS Linear image sensor |
| S3901 | NMOS Linear image sensor |
| S3901-128Q | NMOS Linear image sensor |
| S3901-256Q | NMOS Linear image sensor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29GL128P90FAIR10 | 功能描述:閃存 128MB 3.0-3.6V 90ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S29GL128P90FAIR20 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 16MX8/8MX16 90NS 64BGA - Trays 制造商:Spansion 功能描述:SPZS29GL128P90FAIR20 IC 128M PAGE-MODE 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 128Mbit 16M/8M x 8bit/16bit 90ns 64-Pin Fortified BGA Tray |
| S29GL128P90FFCR10 | 功能描述:閃存 128MB 3.0-3.6V 90ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S29GL128P90FFCR12 | 功能描述:閃存 128M 3.0V 90ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S29GL128P90FFCR20 | 功能描述:閃存 128MB 3.0-3.6V 90ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。