參數資料
型號： S29GL128M90TFIR12
廠商： SPANSION LLC
元件分類： DRAM
英文描述： 3.0 Volt-only Page Mode Flash Memory featuring 0.23 um MirrorBit process technology
中文描述： 8M X 16 FLASH 3V PROM, 90 ns, PDSO56
封裝： LEAD FREE, MO-142-EC, TSOP-56
文件頁數： 109/160頁
文件大小： 2142K
代理商： S29GL128M90TFIR12
April 30, 2004 S29GLxxxM_00A5
S29GLxxxM MirrorBit
TM
Flash Family
109
P r e l i m i n a r y
After the Program Resume command is written, the device reverts to program-
ming. The system can determine the status of the program operation using the
DQ7 or DQ6 status bits, just as in the standard program operation. See Write Op-
eration Status for more information.
The system must write the Program Resume command (address bits are don’t
care) to exit the Program Suspend mode and continue the programming opera-
tion. Further writes of the Resume command are ignored. Another Program
Suspend command can be written after the device has resumed programming.
Figure 5. Program Suspend/Program Resume
Chip Erase Command Sequence
Chip erase is a six bus cycle operation. The chip erase command sequence is ini-
tiated by writing two unlock cycles, followed by a set-up command. Two
additional unlock write cycles are then followed by the chip erase command,
which in turn invokes the Embedded Erase algorithm. The device does
not
require
the system to preprogram prior to erase. The Embedded Erase algorithm auto-
matically preprograms and verifies the entire memory for an all zero data pattern
prior to electrical erase. The system is not required to provide any controls or tim-
ings during these operations. Table
31
and Table
32
show the address and data
requirements for the chip erase command sequence.
When the Embedded Erase algorithm is complete, the device returns to the read
mode and addresses are no longer latched. The system can determine the status
of the erase operation by using DQ7, DQ6, or DQ2. Refer to the Write Operation
Status section for information on these status bits.
Program Operation
or Write-to-Buffer
Sequence in Progress
Write Program Suspend
Command Sequence
Command is also valid for
Erase-suspended-program
operations
Autoselect and SecSi Sector
read operations are also allowed
Data cannot be read from erase- or
program-suspended sectors
Write Program Resume
Command Sequence
Read data as
required
Done
reading
No
Yes
Write address/data
XXXh/30h
Device reverts to
operation prior to
Program Suspend
Write address/data
XXXh/B0h
Wait 15
μ
s
相關PDF資料
PDF描述
S29GL128M90TFIR13 3.0 Volt-only Page Mode Flash Memory featuring 0.23 um MirrorBit process technology
S29GL128M90TFIR20 3.0 Volt-only Page Mode Flash Memory featuring 0.23 um MirrorBit process technology
S29GL128M90TFIR22 3.0 Volt-only Page Mode Flash Memory featuring 0.23 um MirrorBit process technology
S29GL128M90TFIR23 MOSFET, Switching; VDSS (V): 100; ID (A): 4; Pch : 3; RDS (ON) typ. (ohm) @10V: 0.12; RDS (ON) typ. (ohm) @4V[4.5V]: 0.15; RDS (ON) typ. (ohm) @2.5V: -; Ciss (pF) typ: 420; toff (µs) typ: 0.11; Package: SOP-8
S29GL128M90TFIR80 3.0 Volt-only Page Mode Flash Memory featuring 0.23 um MirrorBit process technology
相關代理商/技術參數
參數描述
S29GL128N10FFI010 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 128Mbit 16M/8M x 8bit/16bit 100ns 64-Pin Fortified BGA Tray 制造商:Spansion 功能描述:MIRRORBIT FLASH 128MB SMD 29LV128
S29GL128N10FFI020 制造商:Spansion 功能描述:Flash - NOR IC
S29GL128N10TF101 制造商:Spansion 功能描述:
S29GL128N10TFI010 功能描述:IC FLASH 制造商:cypress semiconductor corp 系列:GL-N 包裝:托盤 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:128Mb （16M x 8，8M x 16） 寫周期時間 - 字，頁:100ns 訪問時間:100ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:56-TFSOP（0.724"，18.40mm 寬） 供應商器件封裝:56-TSOP 標準包裝:91
S29GL128N10TFI020 制造商:Spansion 功能描述:S29GL128N10TFI020 制造商:Spansion 功能描述:Flash - NOR IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*