- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C6P366D0A0100 4-BIT, FLASH, 4.1 MHz, MICROCONTROLLER, UUC102 PDF資料下載
參數資料
| 型號： | S1C6P366D0A0100 |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, FLASH, 4.1 MHz, MICROCONTROLLER, UUC102 |
| 封裝： | DIE-102 |
| 文件頁數： | 14/84頁 |
| 文件大?。?/td> | 1740K |
| 代理商： | S1C6P366D0A0100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
S1C6P366 TECHNICAL MANUAL
EPSON
11
CHAPTER 3: CPU, PROM, RAM
CHAPTER
3 CPU, PROM, RAM
3.1 CPU
The S1C6P366 has a 4-bit core CPU S1C63000 built-in as its CPU part.
Refer to the "S1C63000 Core CPU Manual" for the S1C63000.
Note: The SLP instruction cannot be used because the SLEEP operation is not assumed in the S1C6P366.
3.2 Code PROM
The built-in code PROM is a PROM for loading programs, and has a capacity of 16,384 steps
× 13 bits.
The core CPU can linearly access the program space up to step FFFFH from step 0000H, however, the
program area of the S1C6P366 is step 0000H to step 3FFFH. The program start address after initial reset is
assigned to step 0110H. The non-maskable interrupt (NMI) vector and hardware interrupt vectors are
allocated to step 0100H and steps 0102H–010EH, respectively.
0000H
3FFFH
4000H
FFFFH
0000H
0100H
0102H
010EH
0110H
Program area
NMI vector
Hardware
interrupt vectors
Program start address
Program area
PROM
Unused area
13 bits
S1C63000 core CPU
program space
S1C6P366
program area
Fig. 3.2.1 Configuration of code PROM
3.3 RAM
The RAM is a data memory for storing various kinds of data, and has a capacity of 2,048 words
× 4 bits.
The RAM area is assigned to addresses 0000H to 07FFH on the data memory map. Addresses 0100H to
01FFH are 4-bit/16-bit data accessible areas and in other areas it is only possible to access 4-bit data.
When programming, keep the following points in mind.
(1) Part of the RAM area is used as a stack area for subroutine call and register evacuation, so pay
attention not to overlap the data area and stack area.
(2) The S1C63000 core CPU handles the stack using the stack pointer for 4-bit data (SP2) and the stack
pointer for 16-bit data (SP1).
16-bit data are accessed in stack handling by SP1, therefore, this stack area should be allocated to the
area where 4-bit/16-bit access is possible (0100H to 01FFH). The stack pointers SP1 and SP2 change
cyclically within their respective range: the range of SP1 is 0000H to 03FFH and the range of SP2 is
0000H to 00FFH. Therefore, pay attention to the SP1 value because it may be set to 00FFH or less
exceeding the 4-bit/16-bit accessible range in the S1C6P366. Memory accesses except for stack opera-
tions by SP1 are 4-bit data access.
After initial reset, all the interrupts including NMI are masked until both the stack pointers SP1 and
SP2 are set by software. Further, if either SP1 or SP2 is re-set when both are set already, the interrupts
including NMI are masked again until the other is re-set. Therefore, the settings of SP1 and SP2 must
be done as a pair.
相關PDF資料 |
PDF描述 |
|---|---|
| S1C6P466D0A0A00 | MICROCONTROLLER, UUC140 |
| S1C6S2L7D | 4-BIT, MROM, 0.032 MHz, MICROCONTROLLER, UUC58 |
| S1C6S2A7F | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60 |
| S1C6S2B7F | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60 |
| S1C6S2N7D | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, UUC58 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C-6-S | 制造商:GRIPCO 功能描述: |
| S1C7309X | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR |
| S1C7309X01 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR |
| S1C88349 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
| S1C88649 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。