- 您現在的位置：買賣IC網 > PDF目錄1966 > QLX4600LIQSR (Intersil)IC EQUALIZER REC 6.25GBPS 46QFN PDF資料下載
參數資料
| 型號： | QLX4600LIQSR |
| 廠商： | Intersil |
| 文件頁數： | 11/23頁 |
| 文件大小： | 0K |
| 描述： | IC EQUALIZER REC 6.25GBPS 46QFN |
| 標準包裝： | 100 |
| 系列： | QLx™ |
| 應用： | 銅電纜模塊 |
| 電源電壓： | 1.1 V ~ 1.3 V |
| 封裝/外殼： | 46-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 46-TQFN |
| 包裝： | 帶卷 (TR) |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁
19
FN6981.1
November 19, 2009
Detection Threshold (DT) Pin Functionality
The QLx4600-SL30 is capable of maintaining periods of
line silence on any of its four channels by monitoring
each channel for loss of signal (LOS) conditions and
subsequently muting the outputs of a respective channel
when such a condition is detected. A reference current
applied to the detection threshold (DT) pin is used to set
the LOS threshold of the internal signal detection
circuitry. Current control on the DT pin is done via one or
two external resistors. Nominally, both a pull-up and
pull-down resistor are tied to the DT pin (Figure 32A),
but if adequate control of the supply voltage is
maintained to within ±3% of 1.2V, then a simple
pull-down resistor is adequate (as in Figure 32B).
Resistors used should be at least 1/16W, with ±1%
precision.
The internal bias point of the DT pin, nominally 1.05V, is
used in conjunction with the voltage divider (R1 and R2)
shown in Figure 32A to set the reference current on the
DT pin.
Case 1: Channels with less than or equal to 25dB loss at
2.5GHz (1Gb/s to 6Gb/s):
For signals transmitted on channels having less than
or equal to 25dB of loss at 2.5GHz, the optimal DT
reference current is 0A. This optimal reference
current may be achieved by either leaving the DT pin
floating, or tying the DT pin to ground (GND) with a
10MΩ resistor
Case 2: Channels with greater 25dB loss at 2.5GHz
(1Gb/s to 6Gb/s):
For channels exhibiting more than 25dB of total loss
(this includes cable or FR-4 loss) the DT pin should
be configured for a reference sink current (coming
out of the DT pin) of approximately 2A. A typical
configuration for a 2A sink current is given in
utilized, a 525kΩ resistor would be used.
FIGURE 32A.
FIGURE 32B.
FIGURE 32C.
FIGURE 32.
QLx4600-SL30
相關PDF資料 |
PDF描述 |
|---|---|
| QLX4600SIQSR | IC EQUALIZER REC 6.25GBPS 46QFN |
| R5F100GEAFB#V0 | MCU 16BIT 64KB FLASH 48LQFP |
| R5F2135CMNFP#V0 | IC MICROCONTROLLER |
| R5F562N8ADBG#U0 | MCU 32BIT FLASH 512KROM 176LFBGA |
| R5F5630ADDFB#V0 | MCU RX630 768KB FLASH 144-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| QLX4600LIQT7 | 功能描述:接口 - 專用 6 GBS QD CH LANE EXTENDER RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| QLX4600MIBQ15 | 制造商:Intersil Corporation 功能描述:IC LINEAR |
| QLX4600-S30 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad Lane Extender |
| QLX4600SIQSR | 功能描述:接口 - 專用 6 GBS QD CH LANE EXTENDER RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| QLX4600SIQT7 | 功能描述:接口 - 專用 6 GBS QD CH LANE EXTENDER RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。