- 您現在的位置：買賣IC網 > PDF目錄385747 > PSD813F2A (意法半導體) Flash In-System Programmable(ISP) Peripherals For 8-bit MCUs(用于八位MCU的閃速在系統可編程外圍芯片) PDF資料下載
參數資料
| 型號： | PSD813F2A |
| 廠商： | 意法半導體 |
| 英文描述： | Flash In-System Programmable(ISP) Peripherals For 8-bit MCUs(用于八位MCU的閃速在系統可編程外圍芯片) |
| 中文描述： | Flash在系統可編程（ISP）為周邊8位微控制器（用于八位微控制器的閃速在系統可編程外圍芯片） |
| 文件頁數： | 59/103頁 |
| 文件大小： | 1180K |
| 代理商： | PSD813F2A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁當前第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁
59/103
PSD8XXF2/3/4/5
Automatic Power-down (APD) Unit and Power-
down Mode.
The APD Unit, shown in Figure 29,
puts the PSD8XXFX into Power-down mode by
monitoring the activity of Address Strobe (ALE/AS,
PD0). If the APD Unit is enabled, as soon as activ-
ity on Address Strobe (ALE/AS, PD0) stops, a four
bit counter starts counting. If Address Strobe
(ALE/AS, PD0) remains inactive for fifteen clock
periods of CLKIN (PD1), Power-down (PDN) goes
High, and the PSD8XXFX enters Power-down
mode, as discussed next.
Power-down Mode.
By default, if you enable the
APD Unit, Power-down mode is automatically en-
abled. The device enters Power-down mode if Ad-
dress Strobe (ALE/AS, PD0) remains inactive for
fifteen periods of CLKIN (PD1).
The following should be kept in mind when the
PSD8XXFX is in Power-down mode:
I
If Address Strobe (ALE/AS, PD0) starts pulsing
again, the PSD8XXFX returns to normal
Operating mode. The PSD8XXFX also returns
to normal Operating mode if either PSD Chip
Select Input (CSI, PD2) is Low or the Reset
(RESET) input is High.
I
The MCU address/data bus is blocked from all
memory and PLDs.
I
Various signals can be blocked (prior to Power-
down mode) from entering the PLDs by setting
the appropriate bits in the PMMR registers. The
blocked signals include MCU control signals
and the common CLKIN (PD1). Note that
blocking CLKIN (PD1) from the PLDs does not
block CLKIN (PD1) from the APD Unit.
I
All PSD8XXFX memories enter Standby mode
and are drawing standby current. However, the
PLD and I/O ports blocks do not
go into Standby
Mode because you don’t want to have to wait for
the logic and I/O to “wake-up” before their
outputs can change. See Table 28 for Power-
down mode effects on PSD8XXFX ports.
I
Typical standby current is of the order of
microamperes. These standby current values
assume that there are no transitions on any PLD
input.
Table 28. Power-down Mode’s Effect on Ports
Figure 29. APD Unit
Table 29. PSD8XXFX Timing and Stand-by Current during Power-down Mode
Note: 1. Power-down does not affect the operation of the PLD. The PLD operation in this mode is based only on the Turbo bit.
2. Typical current consumption assuming no PLD inputs are changing state and the PLD Turbo bit is 0.
Port Function
Pin Level
MCU I/O
No Change
PLD Out
No Change
Address Out
Undefined
Data Port
Tri-State
Peripheral I/O
Tri-State
Mode
PLD Propagation
Delay
Memory
Access Time
Access Recovery Time
to Normal Access
Typical Stand-by Current
5V V
CC
3V V
CC
Power-down
Normal t
PD
(Note
1
)
No Access
t
LVDV
75 μA (Note
2
)
25 μA (Note
2
)
APD EN
PMMR0 BIT 1=1
ALE
RESET
CSI
CLKIN
TRANSITION
DETECTION
EDGE
DETECT
APD
COUNTER
POWER DOWN
(PDN)
SELECT
DISABLE BUS
INTERFACE
EEPROM SELECT
FLASH SELECT
SRAM SELECT
PD
CLR
PD
DISABLE
FLASH/EEPROM/SRAM
PLD
AI02891
相關PDF資料 |
PDF描述 |
|---|---|
| PSD813F2V | Flash In-System Programmable (ISP) Peripherals for8-bits MCUs, 3V |
| PSD813F2V-15J1T | Flash In-System Programmable (ISP) Peripherals for8-bits MCUs, 3V |
| PSD833F2V | Flash In-System Programmable (ISP) Peripherals for8-bits MCUs, 3V |
| PSD833F2V-15J1T | Flash In-System Programmable (ISP) Peripherals for8-bits MCUs, 3V |
| PSD853F2V | Flash In-System Programmable (ISP) Peripherals for8-bits MCUs, 3V |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PSD813F2A-12J | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
| PSD813F2A-12JI | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
| PSD813F2A-12JIT | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
| PSD813F2A-12JT | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
| PSD813F2A-12M | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
發布緊急采購，3分鐘左右您將得到回復。