- 您現在的位置：買賣IC網 > PDF目錄3874 > PIC16F1527-I/PT (Microchip Technology)MCU 28KB FLASH 1536B RAM 64-TQFP PDF資料下載
參數資料
| 型號： | PIC16F1527-I/PT |
| 廠商： | Microchip Technology |
| 文件頁數： | 87/94頁 |
| 文件大?。?/td> | 0K |
| 描述： | MCU 28KB FLASH 1536B RAM 64-TQFP |
| 產品培訓模塊： | Configurable Logic Cell 8-bit PIC® Microcontroller Portfolio |
| 特色產品： | Extreme Low Power (XLP) Microcontrollers |
| 標準包裝： | 160 |
| 系列： | PIC® XLP™ 16F |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 20MHz |
| 連通性： | I²C，LIN，SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，POR，PWM，WDT |
| 輸入/輸出數： | 54 |
| 程序存儲器容量： | 28KB（16K x 14） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 1.5K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.3 V ~ 5.5 V |
| 數據轉換器： | A/D 30x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 64-TQFP |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁當前第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁
2011 Microchip Technology Inc.
Preliminary
DS41458B-page 53
PIC16(L)F1526/27
5.2
Clock Source Types
Clock sources can be classified as external or internal.
External clock sources rely on external circuitry for the
clock source to function. Examples are: oscillator mod-
ules (EC mode), quartz crystal resonators or ceramic
resonators (LP, XT and HS modes) and Resis-
tor-Capacitor (RC) mode circuits.
Internal clock sources are contained internally within the
oscillator module. The internal oscillator block has two
internal oscillators that are used to generate the internal
system clock sources: the 16 MHz High-Frequency
Internal Oscillator and the 31 kHz Low-Frequency
Internal Oscillator (LFINTOSC).
The system clock can be selected between external or
internal clock sources via the System Clock Select
(SCS) bits in the OSCCON register. See Section 5.3
for additional information.
5.2.1
EXTERNAL CLOCK SOURCES
An external clock source can be used as the device
system clock by performing one of the following
actions:
Program the FOSC<2:0> bits in the Configuration
Word 1 to select an external clock source that will
be used as the default system clock upon a
device Reset.
Write the SCS<1:0> bits in the OSCCON register
to switch the system clock source to:
- Secondary oscillator during run-time, or
- An external clock source determined by the
value of the FOSC bits.
See Section 5.3 “Clock Switching”for more informa-
tion.
5.2.1.1
EC Mode
The External Clock (EC) mode allows an externally
generated logic level signal to be the system clock
source. When operating in this mode, an external clock
source
is
connected
to
the
OSC1
input.
OSC2/CLKOUT is available for general purpose I/O or
CLKOUT. Figure 5-2 shows the pin connections for EC
mode.
EC mode has three power modes to select from through
Configuration Word 1:
High power, 4-20 MHz (FOSC = 111)
Medium power, 0.5-4 MHz (FOSC = 110)
Low power, 0-0.5 MHz (FOSC = 101)
The Oscillator Start-up Timer (OST) is disabled when
EC mode is selected. Therefore, there is no delay in
operation after a Power-on Reset (POR) or wake-up
from Sleep. Because the PIC MCU design is fully
static, stopping the external clock input will have the
effect of halting the device while leaving all data intact.
Upon restarting the external clock, the device will
resume operation as if no time had elapsed.
FIGURE 5-2:
EXTERNAL CLOCK (EC)
MODE OPERATION
5.2.1.2
LP, XT, HS Modes
The LP, XT and HS modes support the use of quartz
crystal resonators or ceramic resonators connected to
OSC1 and OSC2 (Figure 5-3). The three modes select
a low, medium or high gain setting of the internal
inverter-amplifier to support various resonator types
and speed.
LP
Oscillator mode selects the lowest gain setting of the
internal inverter-amplifier. LP mode current consumption
is the least of the three modes. This mode is designed to
drive only 32.768 kHz tuning-fork type crystals (watch
crystals).
XT
Oscillator mode selects the intermediate gain
setting of the internal inverter-amplifier. XT mode
current consumption is the medium of the three modes.
This mode is best suited to drive resonators with a
medium drive level specification.
HS
Oscillator mode selects the highest gain setting of the
internal inverter-amplifier. HS mode current consumption
is the highest of the three modes. This mode is best
suited for resonators that require a high drive setting.
Figure 5-3 and Figure 5-4 show typical circuits for
quartz crystal and ceramic resonators, respectively.
OSC1/CLKIN
OSC2/CLKOUT
Clock from
Ext. System
PIC MCU
FOSC/4 or I/O(1)
Note
1:
Output depends upon CLKOUTEN bit of the
Configuration Word 1.
相關PDF資料 |
PDF描述 |
|---|---|
| PIC18LF25J10T-I/ML | IC PIC MCU FLASH 16KX16 28QFN |
| PIC16LF724-E/PT | IC PIC MCU FLASH 7KB 44-TQFP |
| PIC18LF44J10T-I/ML | IC PIC MCU FLASH 8KX16 44QFN |
| PIC16LF727-I/PT | IC PIC MCU FLASH 8K 1.8V 44-TQFP |
| PIC24F08KA102-I/SO | IC PIC MCU FLASH 8K 28-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC16F1527T-I/MR | 功能描述:8位微控制器 -MCU 28KB FL 1536B RAM 10bit ADC 1.8-5.5V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC16F1527T-I/PT | 功能描述:8位微控制器 -MCU 14KB Flash RAM 768b nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC16F1613-E/P | 制造商:Microchip Technology Inc 功能描述:3.5KB Flash, 256 RAM, 32MHz Int. Osc, 10bit ADC, ZCD, WWDT, CRC, 14 PDIP .300in |
| PIC16F1613-I/SL | 制造商:Microchip Technology Inc 功能描述:3.5KB FLASH, 256 RAM, 32MHZ INT. OSC, 10BIT ADC, ZCD, WWDT, - Rail/Tube |
| PIC16F1613-I/ST | 制造商:Microchip Technology Inc 功能描述:3.5KB FLASH, 256 RAM, 32MHZ INT. OSC, 10BIT ADC, ZCD, WWDT, - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。