- 您現在的位置：買賣IC網 > PDF目錄3874 > PIC16F1527-I/PT (Microchip Technology)MCU 28KB FLASH 1536B RAM 64-TQFP PDF資料下載
參數資料
| 型號： | PIC16F1527-I/PT |
| 廠商： | Microchip Technology |
| 文件頁數： | 51/94頁 |
| 文件大?。?/td> | 0K |
| 描述： | MCU 28KB FLASH 1536B RAM 64-TQFP |
| 產品培訓模塊： | Configurable Logic Cell 8-bit PIC® Microcontroller Portfolio |
| 特色產品： | Extreme Low Power (XLP) Microcontrollers |
| 標準包裝： | 160 |
| 系列： | PIC® XLP™ 16F |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 20MHz |
| 連通性： | I²C，LIN，SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，POR，PWM，WDT |
| 輸入/輸出數： | 54 |
| 程序存儲器容量： | 28KB（16K x 14） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 1.5K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.3 V ~ 5.5 V |
| 數據轉換器： | A/D 30x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 64-TQFP |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁
216
7810C–AVR–10/12
Atmel ATmega328P [Preliminary]
Figure 21-10. Interfacing the Application to the TWI in a Typical Transmission
1.
The first step in a TWI transmission is to transmit a START condition. This is done by
writing a specific value into TWCR, instructing the TWI hardware to transmit a START
condition. Which value to write is described later on. However, it is important that the
TWINT bit is set in the value written. Writing a one to TWINT clears the flag. The TWI will
not start any operation as long as the TWINT bit in TWCR is set. Immediately after the
application has cleared TWINT, the TWI will initiate transmission of the START condition.
2.
When the START condition has been transmitted, the TWINT Flag in TWCR is set, and
TWSR is updated with a status code indicating that the START condition has success-
fully been sent.
3.
The application software should now examine the value of TWSR, to make sure that the
START condition was successfully transmitted. If TWSR indicates otherwise, the applica-
tion software might take some special action, like calling an error routine. Assuming that
the status code is as expected, the application must load SLA+W into TWDR. Remember
that TWDR is used both for address and data. After TWDR has been loaded with the
desired SLA+W, a specific value must be written to TWCR, instructing the TWI hardware
to transmit the SLA+W present in TWDR. Which value to write is described later on.
However, it is important that the TWINT bit is set in the value written. Writing a one to
TWINT clears the flag. The TWI will not start any operation as long as the TWINT bit in
TWCR is set. Immediately after the application has cleared TWINT, the TWI will initiate
transmission of the address packet.
4.
When the address packet has been transmitted, the TWINT Flag in TWCR is set, and
TWSR is updated with a status code indicating that the address packet has successfully
been sent. The status code will also reflect whether a Slave acknowledged the packet or
not.
5.
The application software should now examine the value of TWSR, to make sure that the
address packet was successfully transmitted, and that the value of the ACK bit was as
expected. If TWSR indicates otherwise, the application software might take some special
action, like calling an error routine. Assuming that the status code is as expected, the
application must load a data packet into TWDR. Subsequently, a specific value must be
written to TWCR, instructing the TWI hardware to transmit the data packet present in
TWDR. Which value to write is described later on.
START
SLA+W
A
Data
A
STOP
1. Application
writes to TWCR to
initiate
transmission of
START
2. TWINT set.
Status code indicates
START condition sent
4. TWINT set.
Status code indicates
SLA+W sent, ACK
received
6. TWINT set.
Status code indicates
data sent, ACK received
3. Check TWSR to see if START was
sent. Application loads SLA+W into
TWDR, and loads appropriate control
signals into TWCR, makin sure that
TWINT is written to one,
and TWSTA is written to zero.
5. Check TWSR to see if SLA+W was
sent and ACK received.
Application loads data into TWDR, and
loads appropriate control signals into
TWCR, making sure that TWINT is
written to one
7. Check TWSR to see if data was sent
and ACK received.
Application loads appropriate control
signals to send STOP into TWCR,
making sure that TWINT is written to one
TWI bus
Indicates
TWINT set
Application
Action
TWI
Hardw
are
Action
相關PDF資料 |
PDF描述 |
|---|---|
| PIC18LF25J10T-I/ML | IC PIC MCU FLASH 16KX16 28QFN |
| PIC16LF724-E/PT | IC PIC MCU FLASH 7KB 44-TQFP |
| PIC18LF44J10T-I/ML | IC PIC MCU FLASH 8KX16 44QFN |
| PIC16LF727-I/PT | IC PIC MCU FLASH 8K 1.8V 44-TQFP |
| PIC24F08KA102-I/SO | IC PIC MCU FLASH 8K 28-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC16F1527T-I/MR | 功能描述:8位微控制器 -MCU 28KB FL 1536B RAM 10bit ADC 1.8-5.5V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC16F1527T-I/PT | 功能描述:8位微控制器 -MCU 14KB Flash RAM 768b nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC16F1613-E/P | 制造商:Microchip Technology Inc 功能描述:3.5KB Flash, 256 RAM, 32MHz Int. Osc, 10bit ADC, ZCD, WWDT, CRC, 14 PDIP .300in |
| PIC16F1613-I/SL | 制造商:Microchip Technology Inc 功能描述:3.5KB FLASH, 256 RAM, 32MHZ INT. OSC, 10BIT ADC, ZCD, WWDT, - Rail/Tube |
| PIC16F1613-I/ST | 制造商:Microchip Technology Inc 功能描述:3.5KB FLASH, 256 RAM, 32MHZ INT. OSC, 10BIT ADC, ZCD, WWDT, - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。