- 您現在的位置：買賣IC網 > PDF目錄367815 > PCF2113AUF4 (NXP Semiconductors N.V.) LCD controllers/drivers PDF資料下載
參數資料
| 型號： | PCF2113AUF4 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | LCD controllers/drivers |
| 中文描述： | LCD控制器/驅動器 |
| 文件頁數： | 23/72頁 |
| 文件大?。?/td> | 332K |
| 代理商： | PCF2113AUF4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
2001 Dec 19
23
Philips Semiconductors
Product specification
LCD controllers/drivers
PCF2113x
8
INSTRUCTIONS
OnlytwoPCF2113xregisters,theInstructionRegister (IR)
and the Data Register (DR) can be directly controlled by
the microcontroller. Before internal operation, control
information is stored temporarily in these registers, to
allow interfacing to various types of microcontrollers which
operate at different speeds or to allow interface to
peripheral control ICs.
The instruction set for I
2
C-bus commands is given in
Table 4.
The PCF2113x operation is controlled by the instructions
shown in Table 5 together with their execution time.
Details are explained in subsequent sections.
Instructions are of 4 types, those that:
1.
Designate PCF2113x functions such as display
format, data length, etcetera.
2.
Set internal RAM addresses
3.
Perform data transfer with internal RAM
4.
Others.
In normal use, category 3 instructions are used most
frequently. However, automatic incrementing by 1
(or decrementing by 1) of internal RAM addresses after
each data write lessens the microcontroller program load.
The display shift in particular can be performed
concurrently with display data write, enabling the designer
to develop systems in minimum time with maximum
programming efficiency.
During internal operation, no instructions other than the
‘read busy flag’ and ‘read address’ instructions will be
executed. Because the busy flag is set to a logic 1 while an
instruction is being executed, check to ensure it is a logic 0
before sending the next instruction or wait for the
maximum instruction execution time, as given in Table 5.
An instruction sent while the busy flag is logic 1 will not be
executed.
Table 4
Instruction set for I
2
C-bus commands
Note
1.
R/W is set together with the slave address.
CONTROL BYTE
COMMAND BYTE
I
2
C-BUS COMMANDS
Co
RS 0
0
0
0
0
0
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
note 1
相關PDF資料 |
PDF描述 |
|---|---|
| PCF2113WUF4 | LCD controllers/drivers |
| PCF2113AU10 | RECTIFIER SBR DUAL 20A 60V 180A-ifsm 650mV-vf 0.5mA-ir TO-220AB 50/TUBE |
| PCF2113EU2 | LCD controllers/drivers |
| PCF2113EUF4 | LCD controllers/drivers |
| PCF2113A | LCD controller/driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCF2113D | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controller/driver |
| PCF2113DH | 制造商:NXP Semiconductors 功能描述:18 X 60 DOTS DOT MAT LCD DRVR AND DSPL CTLR, PQFP100 |
| PCF2113DH/4 | 功能描述:LCD 驅動器 I2C LCD CHARCTR DRVR RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| PCF2113DH/4,557 | 功能描述:LCD 驅動器 I2C LCD CHARCTR DRVR RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| PCF2113DH/F2 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controller/driver |
發布緊急采購，3分鐘左右您將得到回復。