- 您現在的位置：買賣IC網 > PDF目錄367815 > PCF2113AU10 (NXP Semiconductors N.V.) RECTIFIER SBR DUAL 20A 60V 180A-ifsm 650mV-vf 0.5mA-ir TO-220AB 50/TUBE PDF資料下載
參數資料
| 型號： | PCF2113AU10 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | RECTIFIER SBR DUAL 20A 60V 180A-ifsm 650mV-vf 0.5mA-ir TO-220AB 50/TUBE |
| 中文描述： | LCD控制器/驅動器 |
| 文件頁數： | 34/72頁 |
| 文件大?。?/td> | 332K |
| 代理商： | PCF2113AU10 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
2001 Dec 19
34
Philips Semiconductors
Product specification
LCD controllers/drivers
PCF2113x
A master receiver must signal an end of data to the
transmitter by not generating an acknowledge bit on the
last byte that has been clocked out of the slave. In this
event the transmitter must leave the data line HIGH to
enable the master to generate a STOP condition.
10.2.1
I
2
C-
BUS PROTOCOL
Before any data is transmitted on the I
2
C-bus, the device
whichshouldrespondisaddressedfirst.Theaddressingis
always carried out with the first byte transmitted after the
START procedure. The I
2
C-bus configuration for the
different PCF2113x read and write cycles is shown in
Figs 24 to 26. The slow down feature of the I
2
C-bus
protocol (receiver holds SCL LOW during internal
operations) is not used in the PCF2113x.
10.2.2
D
EFINITIONS
Transmitter: the device which sends the data to the bus
Receiver: the device which receives the data from the
bus
Master: the device which initiates a transfer generates
clock signals and terminates a transfer
Slave: the device addressed by a master
Multi-master: more than one master can attempt to
control the bus at the same time without corrupting the
message
Arbitration: procedure to ensure that if more than one
master simultaneously tries to control the bus, only one
is allowed to do so and the message is not corrupted
Synchronization: procedure to synchronize the clock
signals of two or more devices.
MGA807
SDA
SCL
MASTER
TRANSMITTER/
RECEIVER
MASTER
TRANSMITTER
SLAVE
TRANSMITTER/
RECEIVER
SLAVE
RECEIVER
MASTER
TRANSMITTER/
RECEIVER
Fig.20 System configuration.
handbook, full pagewidth
MBC621
data line
stable;
data valid
change
of data
allowed
SDA
SCL
Fig.21 Bit transfer.
相關PDF資料 |
PDF描述 |
|---|---|
| PCF2113EU2 | LCD controllers/drivers |
| PCF2113EUF4 | LCD controllers/drivers |
| PCF2113A | LCD controller/driver |
| PCF2113D | LCD controller/driver |
| PCF2113DU10 | LCD controllers/drivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCF2113AUF4 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controllers/drivers |
| PCF2113D | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controller/driver |
| PCF2113DH | 制造商:NXP Semiconductors 功能描述:18 X 60 DOTS DOT MAT LCD DRVR AND DSPL CTLR, PQFP100 |
| PCF2113DH/4 | 功能描述:LCD 驅動器 I2C LCD CHARCTR DRVR RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| PCF2113DH/4,557 | 功能描述:LCD 驅動器 I2C LCD CHARCTR DRVR RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。