參數資料
型號: OPA603AP
英文描述: High Speed, Current-Feedback, High Voltage OPERATIONAL AMPLIFIER
中文描述: 高速,電流反饋,高電壓運算放大器
文件頁數: 10/12頁
文件大小: 262K
代理商: OPA603AP
OPA603
10
FIGURE 2. Dynamic Response, Inverting Unity-Gain.
SMALL-SIGNAL FREQUENCY RESPONSE
Frequency (Hz)
100k
1M
10M
100M
G
+6
+3
0
–3
–6
100pF
50pF
0pF
20pF
10pF
+
V
IN
V
IN
V
O
150
150
2.5k
2.5k
V = ±15V
2.5k
NOTE: Feedback resistor value
selected for reduced peaking.
C
L
=
V
O
C
L
LARGE SIGNAL PULSE RESPONSE
Input
Output
SMALL-SIGNAL FREQUENCY RESPONSE
Frequency (Hz)
100k
1M
10M
100M
G
+26
+23
+20
+17
+14
100pF
50pF
0pF
20pF
10pF
+
V
IN
V
IN
V
O
3570
402
150
150
NOTE: Feedback resistor value
selected for reduced peaking.
V = ±15V
FIGURE 3. Dynamic Response, Gain = +10.
C
L
=
V
O
402
C
L
LARGE SIGNAL PULSE RESPONSE
Output
Input
With control of the open-loop characteristics of the op amp,
dynamic behavior can be tailored to an application’s require-
ments. Lower feedback resistance gives wider bandwidth,
more frequency-response peaking and more pulse response
overshoot. The higher open-loop gain resulting from lower
feedback network resistors also yields lower distortion.
Higher feedback network resistance gives an over-damped
response with little or no peaking and overshoot. This may
be beneficial when driving capacitive loads. Feedback net-
work impedance can also be varied to optimize dynamic
performance. To achieve wider bandwidth, use a feedback
resistor value somewhat lower than indicated in Figure 4.
EXTENDING BANDWIDTH
For gains less than approximately 20, bandwidth can be
extended by adding a capacitor, C
, in parallel with a lower
value for R
. The optimum feedback resistor value in this
case is far lower than those shown in Figure 1. For
±
15V
operation, select R
F
with the following equation:
APPLICATIONS INFORMATION
For most circuit configurations, the OPA603 current-feed-
back op amp can be treated like a conventional op amp. As
with a conventional op amp, the feedback network con-
nected to the inverting input controls the closed-loop gain.
But with a current-feedback op amp, the impedance of the
feedback network also controls the open-loop gain and
frequency response.
Feedback resistor values can be selected to provide a nearly
constant closed-loop bandwidth over a very wide range of
gain. This is in contrast to a conventional op amp where
circuit bandwidth is inversely proportional to the closed-
loop gain, sharply limiting bandwidth at high gain.
Figures 4a and 4b show appropriate feedback resistor values
versus closed-loop gain for maximum bandwidth with mini-
mal peaking. The dual vertical axes of these curves also
show the resulting bandwidth. Note that the bandwidth
remains nearly constant as gain is increased.
相關PDF資料
PDF描述
OPA603AU High Speed, Current-Feedback, High Voltage OPERATIONAL AMPLIFIER
OPA604 FET-Input, Low Distortion OPERATIONAL AMPLIFIER
OPA604AP FET-Input, Low Distortion OPERATIONAL AMPLIFIER
OPA604AU FET-Input, Low Distortion OPERATIONAL AMPLIFIER
OPA606 Wide-Bandwidth Difet OPERATIONAL AMPLIFIER
相關代理商/技術參數
參數描述
OPA603AU 功能描述:高速運算放大器 SOIC-16 High Speed RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
OPA604 制造商:TI 制造商全稱:Texas Instruments 功能描述:FET-Input, Low Distortion OPERATIONAL AMPLIFIER
OPA604_07 制造商:TI 制造商全稱:Texas Instruments 功能描述:FET-Input, Low Distortion OPERATIONAL AMPLIFIER
OPA604AP 功能描述:音頻放大器 FET-Input Audio Op Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
OPA604AP 制造商:BURR-BROWN 功能描述:IC OP AMP LOW DISTORTION FET 604 制造商:Texas Instruments 功能描述:Operational Amplifier (Op-Amp) IC