- 您現在的位置：買賣IC網 > PDF目錄17166 > OM13032,598 (NXP Semiconductors)BOARD EVAL LPC11U24 PDF資料下載
參數資料
| 型號： | OM13032,598 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 49/74頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL LPC11U24 |
| 標準包裝： | 1 |
| 類型： | MCU |
| 適用于相關產品： | LPC11U24 |
| 所含物品： | 板 |
| 其它名稱： | 568-8599 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁當前第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁
LPC11U2X
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2014. All rights reserved.
Product data sheet
Rev. 2.2 — 11 March 2014
53 of 74
NXP Semiconductors
LPC11U2x
32-bit ARM Cortex-M0 microcontroller
For a bus-powered device, the VBUS signal does not need to be connected to the
USB_VBUS pin (see Figure 28). The USB_CONNECT function can additionally be
connected as shown in Figure 27 to prevent the USB from timing out when there is a
significant delay between power-up and handling USB traffic.
Remark: When a bus-powered circuit as shown in Figure 28 is used, configure the
PIO0_3/USB_VBUS pin for GPIO (PIO0_3) in the IOCON block to ensure that the
USB_CONNECT signal can still be controlled by software. For details on the soft-connect
feature, see the LPC11U2x user manual (Ref. 1).
Remark: When a self-powered circuit is used without connecting VBUS, configure the
PIO0_3/USB_VBUS pin for GPIO (PIO0_3) and provide software that can detect the host
presence through some other mechanism before enabling USB_CONNECT and the
soft-connect feature. Enabling the soft-connect without host presence will lead to USB
compliance failure.
11.2 XTAL input
The input voltage to the on-chip oscillators is limited to 1.8 V. If the oscillator is driven by a
clock in slave mode, it is recommended that the input be coupled through a capacitor with
Ci = 100 pF. To limit the input voltage to the specified range, choose an additional
capacitor to ground Cg which attenuates the input voltage by a factor Ci/(Ci + Cg). In slave
mode, a minimum of 200 mV (RMS) is needed.
Fig 28. USB interface on a bus-powered device
LPC1xxx
VDD
R1
1.5 kΩ
aaa-010179
USB-B
connector
USB_DP
USB_DM
VSS
RS = 33 Ω
REGULATOR
VBUS
相關PDF資料 |
PDF描述 |
|---|---|
| 12RS153C | INDUCTOR RAD 15UH 4A T/H 10X10 |
| V375C12C75B2 | CONVERTER MOD DC/DC 12V 75W |
| GSM11DSEN-S243 | CONN EDGECARD 22POS .156 EYELET |
| LTC1558CS-3.3#TRPBF | IC BACKUP BATT CNTRLR3.3V 16SOIC |
| V375C12C75B | CONVERTER MOD DC/DC 12V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OM13033 | 制造商:NXP Semiconductors 功能描述:EVAL ARM NGX LPC11U24 制造商:NXP Semiconductors 功能描述:LPC11U24, NGX, KEIL, EVAL BOARD 制造商:NXP Semiconductors 功能描述:LPC11U24, NGX, KEIL, EVAL BOARD; Silicon Manufacturer:NXP; Core Architecture:ARM; Core Sub-Architecture:Cortex-M0; Silicon Core Number:LPC11xxx; Silicon Family Name:LPC11Uxx; Features:Evaluation Board for LPC11U24 Microcontroller; ;RoHS Compliant: Yes |
| OM13033,598 | 功能描述:開發板和工具包 - ARM NGX LPC11U24 Eval Board RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
| OM13033598 | 制造商:NXP Semiconductors 功能描述:EVAL ARM NGX LPC11U24 |
| OM13034,598 | 制造商:NXP Semiconductors 功能描述:EVAL, IAR, LPC1347, J-LINK LITE 制造商:NXP Semiconductors 功能描述:EVAL, IAR, LPC1347, J-LINK LITE, Silicon Manufacturer:NXP, Core Architecture:ARM 制造商:NXP Semiconductors 功能描述:EVAL, IAR, LPC1347, J-LINK LITE, Silicon Manufacturer:NXP, Core Architecture:ARM, Core Sub-Architecture:Cortex-M3, Silicon Core Number:LPC1347, Silicon Family Name:LPC1300, Kit Contents:Evaluation Board for LPC1347 , RoHS Compliant: Yes |
| OM13034598 | 制造商:NXP Semiconductors 功能描述:EVAL IAR LPC1347 J-LINK LITE |
發布緊急采購，3分鐘左右您將得到回復。