參數資料
型號： NT68P81-D01013
廠商： Electronic Theatre Controls, Inc.
英文描述： USB Keyboard Micro-Controller
中文描述： USB鍵盤微控制器
文件頁數： 17/30頁
文件大?。?/td> 1003K
代理商： NT68P81-D01013
NT68P81
17
9.7. IN1 Token Interrupt
When an IN TOKEN for endpoint 1 is done, it will set the IN1 flag. If this interrupt is enabled by writing "1" to EIN1 ($0005H,
bit2), it will interrupt the 6502 CPU.
When an interrupt occurs, the CPU jumps to $FFFEH & $FFFFH to execute the interrupt service routine, the IN1 flag must
be cleared by the software.
9.8. IN2 Token Interrupt
When an IN TOKEN for endpoint 2 is done, it will set the IN2 flag. If this interrupt is enabled by writing "1" to EIN2 ($0005H,
bit3), it will interrupt 6502 CPU.
When an interrupt occurs, the CPU jumps to $FFFEH & $FFFFH to execute the interrupt service routine, the IN2 flag must
be cleared by the software.
9.9. STUP (SETUP) Token Interrupt
When a SETUP TOKEN for endpoint 0 is done, it will set the STUP flag. If this interrupt is enabled by writing "1" to ESTUP
($0005H, bit6), it will interrupt 6502 CPU.
When an interrupt occurs, the CPU jumps to $FFFEH & $FFFFH to execute the interrupt service routine, the STUP flag
must be cleared by the software.
9.10. SUSP Interrupt
When USB SIE detects a suspend signal, it sets the SUSP flag. Then the 6502 CPU is interrupted if the interrupt has
already been enabled by writing “1” to ESUSP ($0005H, bit7). If ESUSP flag is cleared, 6502 CPU can’ t be SUSP
interrupted even if SUSP flag is set. SUSP flag can be set by H/W only and can’ t be set/cleared directly by the software
except for writing “1” to CSUSP ($0004H, bit 7) flag to clear SUSP flag.
When an interrupt occurs, the CPU jumps to $FFFEH & $FFFFH to execute the interrupt service routine, the SUSP flag
must be cleared by the software.
10. I/O PORTs
The NT68P81 has 32 pins dedicated to input and output. These pins are grouped into 5 ports, as follows:
PORT0 (P00~P07)
PORT0 is an 8-bit bi-directional CMOS I/O port that is internally pulled high by PMOS. Each pin of PORT0 can be bit
programmed as an input or output port under software control. When programmed as output, data is latched to the port
data register and output to the pin. PORT0 pins with “1” written to them are pulled high by the internal PMOS pull-ups, and
can be used as inputs in that state, then these input signals can be read. The port will output high after the reset.
PORT1 (P10~P17)
: Functions the same as PORT0.
PORT2 (P20~P27)
: Functions the same as PORT0.
PORT3 (P30~P34)
: Functions the same as PORT0. Except for P33/P32 is shared with INT1/INT0 pin. It is also a Schmitt
Trigger input with an interrupt source of falling edge sensitive.
LED:
There are three LED direct sink pins which require no external serial resistors.
The address is mapped to $000DH.
相關PDF資料
PDF描述
NT68P81-D01014 USB Keyboard Micro-Controller
NT68P81H USB Keyboard Micro-Controller
NT78BS5DC9V0.8 Small size, light weight. / Low coil consumption.
NT805-401T SINGLE PORT NT805-XXXT SERIES TRANSFORMER, LAN, SMD 10/100 BASE-TX
NT805-559T SINGLE PORT NT805-XXXT SERIES TRANSFORMER, LAN, SMD 10/100 BASE-TX
相關代理商/技術參數
參數描述
NT6C34CA 制造商:ASTEC 功能描述: 制造商:Emerson Network Power - Embedded Power 功能描述:
NT6DM32M16AD-T1 制造商:Nanya Technology Corporation 功能描述:MOBILE DRAM
NT6DM32M16BD-T1 制造商:NANYA TECHNOLOGY 功能描述:512M LPDDR SDRAM, 32Mx16, 200MHz 制造商:NANYA TECHNOLOGY 功能描述:NT6DM32 Series 1.8 V 512 Mb (32 Mb x 16) 200 MHz SDRAM - FBGA-60
NT6DM64M16BD-T1 制造商:Nanya Technology Corporation 功能描述:MEMORY IC
NT6DM8M32AC-T3 制造商:NANYA TECHNOLOGY 功能描述:NT6DM8M32 Series 1.8 V 256 Mb (8 M x 32) 166 Mhz SDRAM - BGA-90 制造商:NANYA TECHNOLOGY 功能描述:NT6DM8M32AC Series 256-Mbit (8 M x 32) 166 Mhz LPDDR SDRAM - BGA-90
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*