參數資料
型號： NCN6000DTBR2
廠商： ON Semiconductor
文件頁數： 8/36頁
文件大?。?/td> 0K
描述： IC INTERFACE SMART CARD 20TSSOP
產品變化通告： Product Obsolescence 01/Jul/2009
標準包裝： 1
應用： ATM 終端，氣泵，ISM
接口： 微控制器
電源電壓： 2.7 V ~ 6 V
封裝/外殼： 20-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 20-TSSOP
包裝： 標準包裝
安裝類型： 表面貼裝
產品目錄頁面： 1131 (CN2011-ZH PDF)
其它名稱： NCN6000DTBR2OSDKR
NCN6000
http://onsemi.com
16
Programming Mode
The programming mode allows the configuration of the
card power supply, card clock and Card Detection input
logic polarity. These signals (CRD_VCC, CRD_CLK and
CRD_DET) are described in the pin description paragraph
associated with Tables 1 and 3 and Figures 4 and 8.
Programming Mode
Logic Conditions:
Card Output:
CS
= L
PWR_ON = L
A0
= H/L
A1
= H/L
PGM
= L
I/O
= L/H
RESET
= L/H
CRD_VCC = 0 V
CRD_CLK = L
CRD_RST = L
CRD_IO
= H/L depending upon
the previous I/O pin
logic state
The I/O and RESET pins are not connected to the smart
card and become logic inputs to control the NCN6000
programming sequence. The programmed values are
latched upon transition of CS from Low to High, PGM being
Low during the transition.
When a programming mode is validated by a Chip Select
negative going transient, the mode is latched and PGM can
be released to High. This latch is automatically reset when
CS returns to High.
The logic input signals can be set simultaneously, or one
bit a time (using either a STAA or a BSET function), the key
point being the minimum delay between the shorter bit and
the Chip Select pulse. The programmed value is latched into
the NCN6000 register on the CS positive going edge.
PROGRAMMING
2
ms2 ms
1
ms
NORMAL MODE
PGM
I/O
A0
A1
RESET
CS
Figure 8. Minimum Programming Timings
Active Mode
In the active mode, the NCN6000 is selected by the
external MPU and the STATUS pin can be polled to get the
status of either the DCDC converter or the presence of the
card (inserted or not valid). The power is not connected to
the card: CRD_VCC = 0 V.
Active Mode
Logic Conditions:
Card Output:
CS
= L
PWR_ON = L
A0
= L
A1
= L
PGM
= H
I/O
= Z
RESET
= Z
STATUS
= L/H is Card
Inserted?
CRD_VCC = 0 V
CRD_CLK = L
CRD_RST = L
CRD_IO
= H/L depending upon
the previous I/O pin
logic state
The Chip Select pulse [CS] will automatically clear the
previously asserted INT signal upon the positive going
transition.
If a card is present, the MPU shall activate the DCDC
converter by asserting PWR_ON = H. The NCN6000 will
automatically run a power up sequence when the
CRD_VCC reaches the undervoltage level (either VC5H or
VC3H, depending upon the CRD_VCC voltage supply
programmed). The CRD_IO, CRD_RST and CRD_CLK
pins are validated, according to the ISO78163 sequence.
The interface is now in transaction mode and the system is
ready for data exchange through the I/O and RESET lines.
At any time, the microcontroller can change the CRD_CLK
frequency and mode, or the CRD_VCC value as determined
by the card being in use.
相關PDF資料
PDF描述
DS8113-RNG+ IC INTERFACE SMART CARD 28-SOIC
MAX1563ETC+ IC CURR-LIM SW SNGL PROG 12-TQFN
MAX6817EUT+T IC DEBOUNCER SWITCH DUAL SOT23-6
D38999/20MD18PN CONN RCPT 18POS WALL MNT W/PINS
D38999/26FC8PB CONN PLUG 8POS STRAIGHT W/PINS
相關代理商/技術參數
參數描述
NCN6000DTBR2G 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart Card Interface RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
NCN6001 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Smartcard Interface ICs
NCN6001/D 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Compact Smart Card Interface IC
NCN6001_06 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Compact Smart Card Interface IC
NCN6001_0610 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Smartcard Interface ICs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*