- 您現在的位置：買賣IC網 > PDF目錄11790 > NCN6000DTBR2 (ON Semiconductor)IC INTERFACE SMART CARD 20TSSOP PDF資料下載
參數資料
| 型號： | NCN6000DTBR2 |
| 廠商： | ON Semiconductor |
| 文件頁數： | 22/36頁 |
| 文件大小： | 0K |
| 描述： | IC INTERFACE SMART CARD 20TSSOP |
| 產品變化通告： | Product Obsolescence 01/Jul/2009 |
| 標準包裝： | 1 |
| 應用： | ATM 終端，氣泵，ISM |
| 接口： | 微控制器 |
| 電源電壓： | 2.7 V ~ 6 V |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 標準包裝 |
| 安裝類型： | 表面貼裝 |
| 產品目錄頁面： | 1131 (CN2011-ZH PDF) |
| 其它名稱： | NCN6000DTBR2OSDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
NCN6000
http://onsemi.com
29
Bidirectional Level Shifter
The NCN6000 carries out the voltage difference between
the MPU and the Smart Card I/O signals. When the start
sequence is completed, and if no failures have been detected,
the device becomes essentially transparent for the data
transferred on the I/O line. To fulfill the ISO78163
specification, both sides of the I/O line have built in pulsed
circuitry to accelerate the signal rise transient. The I/O line is
connected on both side of the interface by a NMOS switch
which provide the level shifter and, due to its relative high
internal impedance, protects the Smart Card in the event of
data collision. Such a situation could occurs if either the MPU
of the smart card forces a signal in the opposite logic level
direction.
When the CS signal goes High, or if the MPU is running
any of the programming functions, the built in register holds
the previous state presents on the input I/O pin. This
mechanism is useful to force the CRD_IO card pin in either
a High or a Low predefined logic state. It is the responsibility
of the programmer to set up the I/O line according to the
system’s activity
Device Q4 provides a low impedance to ground when the
CRD_IO line is deactivated. This mechanism avoids noise
presence on this line during any of the power operation.
When either side of this level shifter is forced to Low, the
externally connected device will be forward biased by the DC
current flowing through the pull up resistors as depicted in
Figure 30. Since these two resistors will carry 350
mA max
each under the worst case conditions, care must be observed
to make sure the external device will be capable to handle this
level of current. Note: the typical series impedance of the
internal MOS device (Q3, Figure 30) is 400
W.
The oscillograms in Figure 31 give the worst case operation
when the stray capacitance is 15 pF.
Q1
Q2
Q3
GND
Vbat
I/O
200 ns
20 k
CRD_IO
Q4
CRD_VCC
LOGIC
CARD ENABLE
Seq 1
Figure 30. Basic Internal I/O Level Shifter
200 ns
Figure 31. Typical CRD_IO Rise Time
I/O
CRD_IO
CRD_VCC = 5.0 V
Note: The I/O data depends solely upon the smart card ATR
content, the NCN6000 being not involved in these data.
Figure 32. Typical I/O and RST Signals During an ATR Sequence.
CRD_VCC
I/O Card
Answer
Request Sends on
CRD_RST Line
NCN6000
Chip Select
CRD_VCC = 3.0 V
相關PDF資料 |
PDF描述 |
|---|---|
| DS8113-RNG+ | IC INTERFACE SMART CARD 28-SOIC |
| MAX1563ETC+ | IC CURR-LIM SW SNGL PROG 12-TQFN |
| MAX6817EUT+T | IC DEBOUNCER SWITCH DUAL SOT23-6 |
| D38999/20MD18PN | CONN RCPT 18POS WALL MNT W/PINS |
| D38999/26FC8PB | CONN PLUG 8POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCN6000DTBR2G | 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart Card Interface RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| NCN6001 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Smartcard Interface ICs |
| NCN6001/D | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Compact Smart Card Interface IC |
| NCN6001_06 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Compact Smart Card Interface IC |
| NCN6001_0610 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Smartcard Interface ICs |
發布緊急采購，3分鐘左右您將得到回復。