- 您現在的位置：買賣IC網 > PDF目錄383642 > MT8930B (Mitel Networks Corporation) () PDF資料下載
參數資料
| 型號： | MT8930B |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | () |
| 中文描述： | （） |
| 文件頁數： | 21/29頁 |
| 文件大小： | 277K |
| 代理商： | MT8930B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Application Note
MSAN-141
A-221
Figure 25 - Longitudinal Conversion Loss Test Circuit
PROTECTION CIRCUITRY
50
Termination:
1.
Z
T
= 400
2.
Z
T
=
68pF
10
μ
F
50
50
100
E
L
V
T
LCL = 20 LOG
V
T
1 : 2
a
b
Z
T
DUT
E
L
～
(
)
a
b
Notes:
1. Transformer T1 should
have a passband of at least
300 kHz to 5 MHz.
2. Lead "b" of termination 2
shown above should be
connected to transformer
pin marked with polarity
dot.
1M
T1
7.0
In compliance with ANSI T1.605 Specification, the
following power fault conditions should not damage
either the NT or the TE:
1.
DC voltage:
a) Amplitude: 56.5 V
b) Current limit: 0.5A
c) Duration: continuous for 5
minutes
2.
AC voltage:
a) Amplitude: 200 V peak
b) Source resistance: 1500
c) Duration: 2 sec on, 4 sec off,
continuous for 5 minutes
3.
Voltage surge: a) Amplitude: 1000 V peak
b) Rise time: 1
μ
s
c) Fall time: 50
μ
s
d) Source capacitance: 15 nF
For part 1 and 2, voltages of each polarity should be
applied between each of the 4-wire S interfaces, and
each other of these wires and the ground reference
of equipment power source. For part 3, fifty surges of
each polarity should be applied between all 4 wires
and the ground reference of the equipment power
source. Each surge is to be simultaneously coupled
to individual S interface wires, each through an
impedance of 15 nF, balanced with respect to
individual wires of the circuit pair.
The selection of the appropriate protection circuitry
to meet these conditions is restricted by the value of
the contributed total capacitance. This value must
not exceed 80 pF when measured on the line side.
Figure 26 - Protection Circuitry for the SNIC
Otherwise, this added capacitance will prevent the
device from complying with I.430 pulse and
impedance templates.
One protection circuit which has been proved to
meet all the stated power fault conditions on the line
side, and provide added protection to the output and
input drivers on the device side, is given in Figure 26.
The total capacitance contributed by this circuit can
be as low as 20 pF (when measured on the transmit
pair of the line side) depending upon the type of
diodes used. These diodes should have similar or
better electrical characteristics than the ones stated
below (typical diodes are the 1N916, 1N4149,
1N4448, 1N4449, 1N4150, 1N4450, 1N4148,
1N3600):
SNIC
LTx
V
Bias
LRx
V
DD
V
DD
10
μ
F
40
V
DD
V
DD
2 : 1
2 : 1
Note: The two diodes at the V
input pin are not needed to
meet I.430 power fault conditions, but they are added for
extra protection.
相關PDF資料 |
PDF描述 |
|---|---|
| MT8931B | () |
| MT8930C-1 | SWITCH, ON-OFF, CHROM/BLK BTN; Switch function type:SPST Latching; Voltage, contact AC max:125V; Voltage, contact DC max:24V; Temp, op. max:85(degree C); Temp, op. min:-40(degree C); Diameter, panel cut-out:13.6mm; Length / Height, RoHS Compliant: Yes |
| MT8930C | Subscriber Network Interface Circuit(用戶網絡接口電路（提供點到點或點到多點數字傳送）) |
| MT8930 | CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit Preliminary Information |
| MT8930C | CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit Preliminary Information |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT8930BC | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Subscriber Network Interface Circuit |
| MT8930BE | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Subscriber Network Interface Circuit |
| MT8930BP | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Subscriber Network Interface Circuit |
| MT8930C | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Subscriber Network Interface Circuit |
| MT8930C-1 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit |
發布緊急采購，3分鐘左右您將得到回復。