- 您現在的位置：買賣IC網 > PDF目錄383642 > MT8930B (Mitel Networks Corporation) () PDF資料下載
參數資料
| 型號： | MT8930B |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | () |
| 中文描述： | （） |
| 文件頁數： | 18/29頁 |
| 文件大?。?/td> | 277K |
| 代理商： | MT8930B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
MSAN-141
Application Note
A-218
Figure 18 - TE Impedance Template (log-log scale)
2500
250
200
100
2
20
80
1000
Frequency (kHz)
Z
the Rx and Tx lines, multiple TEs can be connected
without altering the characteristics impedance of the
line.
5.1
Transmitter Characteristics
The line driver incorporated on the SNIC is a
temperature compensated, voltage limited current
source having a typical I-V characteristics as shown
in Figure 16. This I-V curve reveals that when the
transmitter is active (transmitting a binary 0), the
output impedance will be greater than or equal to the
minimum specified impedance of 20 ohms when
driving the 50 ohm load (i.e., the combination of the
two 100 ohm terminating resistors). When the
transmitter is inactive, the output impedance of the
line driver will exceed the impedance template
shown in Figure 17 for the NT and Figure 18 for the
TE.
The transmitter is configured as a single-ended
driver with a minimum 50 ohm series resistor (refer
to Figure 19).
An external resistor of 40 ohms is used to present
more than 20 ohm load impedance to the
transmission
line
through
(assuming a DC resistance of the transformer as
specified in Table 6). This single-ended drive will
have the effect of reducing the power consumption
by half relative to a differential drive while still
producing a nominal pulse amplitude of 750 mV. The
pulse shape produced by the driver (using
appropriate transformer) will comply to the pulse
template shown in Figure 20. (Figure 20 reveals the
nominal pulse template for a transmit output pulse
with overshoot limited as follows. Any overshoot on
the leading edge of a pulse is permitted up to 5% of
pulse amplitude where this amplitude is defined at
the middle of the signal element. The overshoot must
have 0.5 of its amplitude within 0.25
μ
sec.)
a
2:1
transformer
Figure 19 - Output Equivalent Circuit
5.2 Receiver Characteristics
The MT8930B/31B requires the S-Bus signal to pass
through a 1:2 transformer before being applied to the
bipolar line receiver. The signal from the transformer
is passed through various filters and peak detectors
before the data is recovered (see Figure 21).
The lowpass filter removes any pulse overshoot and
noise which could effect the performance of the peak
detectors. The highpass filter removes low frequency
noise which may be generated by the alternate mark
inversion line code. This highpass filter will also
perform limited post equalization which will improve
the effects of intersymbol interference over long loop
lengths.
Two peak detectors, one for the positive pulses and
the second for negative pulses, are used to establish
an internal reference voltage which, in turn, will be
used as the thresholds for the input recovery circuit.
In the fixed timing mode (i.e., short passive bus) the
filters and peak detectors are bypassed with an input
threshold set to 30% of the nominal pulse amplitude
with no line attenuation. In the adaptive timing mode
the threshold for the data recovery circuit is set to
40% of the output from the peak detectors with a
SNIC
7.5 mA
with max
voltage of
2.5 volt
50
LTx
V
Bias
V
DD
2:1
50
40
相關PDF資料 |
PDF描述 |
|---|---|
| MT8931B | () |
| MT8930C-1 | SWITCH, ON-OFF, CHROM/BLK BTN; Switch function type:SPST Latching; Voltage, contact AC max:125V; Voltage, contact DC max:24V; Temp, op. max:85(degree C); Temp, op. min:-40(degree C); Diameter, panel cut-out:13.6mm; Length / Height, RoHS Compliant: Yes |
| MT8930C | Subscriber Network Interface Circuit(用戶網絡接口電路（提供點到點或點到多點數字傳送）) |
| MT8930 | CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit Preliminary Information |
| MT8930C | CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit Preliminary Information |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT8930BC | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Subscriber Network Interface Circuit |
| MT8930BE | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Subscriber Network Interface Circuit |
| MT8930BP | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Subscriber Network Interface Circuit |
| MT8930C | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Subscriber Network Interface Circuit |
| MT8930C-1 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit |
發布緊急采購，3分鐘左右您將得到回復。