參數資料
型號： MT312T-Y
廠商： Marktech Optoelectronics
英文描述： 2x4mm Rectangular LED Lamps
中文描述： 2x4mm矩形發光二極管
文件頁數： 17/90頁
文件大?。?/td> 318K
代理商： MT312T-Y
Functional Overview
MT312
17
1.7 DiSEqC Transmit and Receive Messages
The MT312 has the capability to send and receive
DiSEqC
messages. Eight registers are provided to
store a message for transmission and a further eight
registers are provided to store a received message.
The received bytes have a parity bit and a parity
error bit in addition to the eight data bits. These
additional bits are read out in following the data bits,
so two byte reads are required for each data byte.
1.7.1 DiSEqC Transmitting Messages
The sequence of events to send a message are as
follows:
1. Load the required message bytes into the
DiSEqC
Instruction register 36, see page 34.
Sequential writes to the same register is achieved
by setting the Inhibit Auto Incrementing (IAI) bit 7
in RADD, the register address byte.
2. Load the number of bytes (less one) in the
DiSEqC
instruction in the register
DISEQC MODE[5:3], see page 32.
3. Set DISEQC MODE[2:0] = 4 to command the
MT312 to encode the data and transmit the
message.
4. Reset DISEQC MODE[2:0] to either 0 or 1
depending on previous setting of 22kHz off or on.
The data loaded into DISEQC INSTR register is
retained, so that if the same message is to be
repeated, the data loading stage 1 above can be
omitted.
1.7.2 DiSEqC Receiving Messages
The MT312 will automatically listen for DiSEqC
messages 5ms after a message has been
transmitted. If a return message is expected, the
DISEQC MODE[2:0] must be set to zero in order to
leave the LNB control signal free for another
DiSEqC
transmitter to respond.
The sequence of events to receive a message are as
follows:
1. Enable DiSEqC2 GPP2 pin 46 as an input by
setting GPP CTRL register 20 B5 to zero.
2. Enable interrupts if the IRQ pin is being used to
interrupt the host processor in DISEQC2 CTRL1
register 121.
3. Monitor DISEQC2 INT register.
4. If B3 = 1 and B1 = 0, there has been no message
received.
5. If a message has been received, B0 will be set, If
B1 is also set the message is complete.
DISEQC2 INT register B7-4 indicate how many
bytes have been received.
6. Read the received message from
DISEQC2 FIFO register 120 by setting the Inhibit
Auto Incrementing (IAI) bit 7 in RADD, the register
address byte and sequentially reading
DISEQC2 FIFO for the indicated number of
bytes. Each data byte read requires two 2-wire
bus reads. The second or the pair of bytes
contains the parity bit and a parity bit error
indicator.
The user may choose to wait for the end of message
indication, before reading the message, if it is known
that the message is not greater than eight bytes.
However, if the length of message is not known, the
message should be read out of the FIFO by the host
as it is being received. Care must be taken to avoid a
FIFO buffer over
fl
ow. DISEQC2 INT register B7-4 will
indicate how many bytes remain in the FIFO.
I
Q
Direct
Conversion
ZIF Tuner
SL1935
Low pass
Filter
Channel
Decoder
MT312
Tank
AGC control
Transport
stream O/P
2-wire bus
control
2-wire bus control
RF I/P
I I/P
Q I/P
Figure 13 - Alternative System Block Diagram - SNIM6
相關PDF資料
PDF描述
MT3371BN Wide Dynamic Range DTMF Receiver
MT3371BS Wide Dynamic Range DTMF Receiver
MT3371BNR Wide Dynamic Range DTMF Receiver
MT3371BSR1 Wide Dynamic Range DTMF Receiver
MT3371BSR Wide Dynamic Range DTMF Receiver
相關代理商/技術參數
參數描述
MT313024 制造商:TE Connectivity 功能描述:
MT3130C4 制造商:TE Connectivity 功能描述:
MT3133-Y 制造商:MARKTECH 制造商全稱:Marktech Corporate 功能描述:Standard 10mm LED Lamps
MT3146-Y 制造商:MARKTECH 制造商全稱:Marktech Corporate 功能描述:1X5 RECTANGULAR LED LAMPS
MT3149 制造商:未知廠家 制造商全稱:未知廠家 功能描述:六路閃燈IC，可選外圍元件改閃燈變順序及狀態。
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*