- 您現在的位置：買賣IC網 > PDF目錄383633 > mPD789326GB-xxx-8ET (NEC Corp.) 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash PDF資料下載
參數資料
| 型號： | mPD789326GB-xxx-8ET |
| 廠商： | NEC Corp. |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash |
| 中文描述： | 8位微控制器與2/4/8K字節在系統可編程閃存 |
| 文件頁數： | 68/96頁 |
| 文件大?。?/td> | 482K |
| 代理商： | MPD789326GB-XXX-8ET |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁當前第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁
Preliminary Product Information U14673EJ1V0PM00
68
μ
PD789322,789324,789326,789327
8. RESET FUNCTION
8.1 Reset Function
The
μ
PD789322, 789324, 789326, and 789327 can be reset using the following three signals.
(1) External reset signal input via RESET pin
(2) Internal reset by watchdog timer runaway time detection
(3) Internal reset using power-on-clear circuit (POC)
The external and internal reset signals are functionally equivalent. When RESET is input, program execution
begins from the addresses written at addresses 0000H and 0001H.
If a low-level signal is applied to the RESET pin, or if the watchdog timer overflows, a reset occurs, causing each
item of the hardware to enter the states listed in Table 8-1. While a reset is being applied, or while the oscillation
frequency is stabilizing immediately after the end of a reset sequence, each pin remains in the high-impedance state.
If a high-level signal is applied to the RESET pin, the reset sequence is terminated, and program execution begins
once the oscillation stabilization time has elapsed. A reset sequence caused by a watchdog timer overflow is
terminated automatically and again program execution begins upon the elapse of the oscillation stabilization time.
Reset by power-ON clear is cleared if the supply voltage rises beyond a specific level, and the program execution is
started after the oscillation stabilization time has elapsed.
Cautions 1. To use an external reset sequence, input a low-level signal to the RESET pin for at least 10
μ
s.
2. When a reset is used to release STOP mode, the data of when STOP mode was entered is
retained during the reset sequence, except for the port pins, which are in the high-impedance
state.
3. The oscillation stabilization time after RESET input or the release of STOP mode by POC can
be selected from 2
15
/f
X
or 2
17
/f
X
by mask option (refer to 9. MASK OPTION).
Figure 8-1. Reset Function Block Diagram
RESET
Count clock
Reset control circuit
Watchdog timer
Stop
Over-
flow
Reset signal
Interrupt function
V
DD
Power-on-clear circuit
相關PDF資料 |
PDF描述 |
|---|---|
| mPD789324 | 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash |
| mPD789326 | 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash |
| MPL135 | Big current (55A), Footprint compatible with most standard, Lower temperature rise at big current, Low DCR, Without noise |
| MPL135-0R4 | Big current (55A), Footprint compatible with most standard, Lower temperature rise at big current, Low DCR, Without noise |
| MPL135-1R0 | Big current (55A), Footprint compatible with most standard, Lower temperature rise at big current, Low DCR, Without noise |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPD789327 | 制造商:NEC 制造商全稱:NEC 功能描述:8-Bit Single-Chip Microcontrollers |
| MPD789327GB-XXX-8ET | 制造商:NEC 制造商全稱:NEC 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLER |
| MPD789425 | 制造商:NEC 制造商全稱:NEC 功能描述:8-Bit Single-Chip Microcontrollers |
| MPD789426 | 制造商:NEC 制造商全稱:NEC 功能描述:8-Bit Single-Chip Microcontrollers |
| MPD789445 | 制造商:NEC 制造商全稱:NEC 功能描述:8-Bit Single-Chip Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。