參數資料
型號： MM908E626
廠商： 飛思卡爾半導體(中國)有限公司
元件分類： 基準電壓源/電流源
英文描述： Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
中文描述： 集成的步進電機驅動器，帶有嵌入式微控制器和LIN串行通信
文件頁數： 14/38頁
文件大小： 507K
代理商： MM908E626
Analog Integrated Circuit Device Data
Freescale Semiconductor
14
908E626
FUNCTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
The 908E626 device was designed and developed as a
highly integrated and cost-effective solution for automotive
and industrial applications. For automotive body electronics,
the 908E626 is well suited to perform stepper motor control,
e.g. for climate or light-levelling control via a 3-wire LIN bus.
This device combines an standard HC08 MCU core
(68HC908EY16) with flash memory together with a
SMARTMOS
IC chip. The
SMARTMOS
IC chip combines
power and control in one chip. Power switches are provided
on the
SMARTMOS
IC configured as four half-bridge
outputs. Other ports are also provided including a selectable
HVDD terminal. An internal voltage regulator is provided on
the
SMARTMOS
IC chip, which provides power to the MCU
chip.
Also included in this device is a LIN physical layer, which
communicates using a single wire. This enables the device to
be compatible with 3-wire bus systems, where one wire is
used for communication, one for battery, and the third for
ground.
FUNCTIONAL TERMINAL DESCRIPTION
See
Figures 1
, for a graphic representation of the various
terminals referred to in the following paragraphs. Also, see
the terminal diagram on
Figures 3
for a depiction of the
terminal locations on the package.
PORT A I /O TERMINALS (PTA0:4)
These terminals are special-function, bidirectional I/O port
terminals that are shared with other functional modules in the
MCU. PTA0 PTA4 are shared with the keyboard interrupt
terminals, KBD0 KBD4.
The PTA5/SPSCK terminal is not accessible in this device
and is internally connected to the SPI clock terminal of the
analog die. The PTA6/
SS
terminal is likewise not accessible.
For details refer to the 68HC908EY16 datasheet.
PORT B I/O TERMINALS (PTB1, PTB3:7)
These terminals are special-function, bidirectional I/O port
terminals that are shared with other functional modules in the
MCU. All terminals are shared with the ADC module. The
PTB6 : PTB7 terminals are also shared with the Timer B
module.
PTB0/AD0 is internally connected to the ADOUT terminal
of the analog die, allowing diagnostic measurements to be
calculated; e.g., current recopy, V
SUP
, etc. The PTB2/AD2
terminal is not accessible in this device.
For details refer to the 68HC908EY16 datasheet.
PORT C I/O TERMINALS (PTC2:4)
These terminals are special-function, bidirectional I/O port
terminals that are shared with other functional modules in the
MCU. For example, PTC2 PTC4 are shared with the ICG
module.
PTC0/MISO and PTC1/MOSI are not accessible in this
device and are internally connected to the MISO and MOSI
SPI terminals of the analog die.
For details refer to the 68HC908EY16 datasheet.
PORT D I /O TERMINALS (PTD0:1)
PTD1/ TACH1 and PTD0/ TACH0/BEMF are special-
function, bidirectional I /O port terminals that can also be
programmed to be timer terminals.
In step motor applications the PTD0 terminal should be
connected to the BEMF output of the analog die in order to
evaluate the BEMF signal with a special BEMF module of the
MCU.
PTD1 terminal is recommended for use as an output
terminal for generating the FGEN signal (PWM signal) if
required by the application.
PORT E I /O TERMINAL (PTE1)
PTE1/ RXD and PTE0/ TXD are special-function,
bidirectional I/O port terminals that can also be programmed
to be enhanced serial communication.
PTE0/TXD is internally connected to the TXD terminal of
the analog die.
The connection for the receiver must be done
externally.
EXTERNAL INTERRUPT TERMINAL (
IRQ
)
The
IRQ
terminal is an asynchronous external interrupt
terminal. This terminal contains an internal pullup resistor that
is always activated, even when the
IRQ
terminal is pulled
LOW.
For details refer to the 68HC908EY16 datasheet.
EXTERNAL RESET TERMINAL (
RST
)
A logic [0] on the
RST
terminal forces the MCU to a known
startup state.
RST
is bidirectional, allowing a reset of the
entire system. It is driven LOW when any internal reset
source is asserted.
This terminal contains an internal pullup resistor that is
always activated, even when the reset terminal is pulled
LOW.
For details refer to the 68HC908EY16 datasheet.
相關PDF資料
PDF描述
MMA1200D Surface Mount Micromachined Accelerometer(表面安裝微電機加速計)
MMA1200 Surface Mount Micromachined Accelerometer
MMA1210D Surface Mount Micromachined Accelerometer(表面安裝微電機加速計)
MMA1210 Surface Mount Micromachined Accelerometer
MMA1211D Surface Mount Micromachined Accelerometer(表面安裝微電機加速計)
相關代理商/技術參數
參數描述
MM908E626AVDWB 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MM908E626AVDWB/R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
MM908E626AVEK 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER W/MCU RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MM908E626AVPEK 功能描述:8位微控制器 -MCU MCU + LIN + MOTOR DRIVER RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MM908E626AVPEKR2 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*