- 您現在的位置：買賣IC網 > PDF目錄98023 > MM58167MWC (NATIONAL SEMICONDUCTOR CORP) 0 TIMER(S), REAL TIME CLOCK, UUC24 PDF資料下載
參數資料
| 型號： | MM58167MWC |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 時鐘/數據恢復及定時提取 |
| 英文描述： | 0 TIMER(S), REAL TIME CLOCK, UUC24 |
| 封裝： | WAFER-24 |
| 文件頁數： | 7/13頁 |
| 文件大?。?/td> | 195K |
| 代理商： | MM58167MWC |
Functional Description
Real Time Counter
The real time counter is divided into 4-bit digits with 2 digits
being accessed during any read or write cycle Each digit
represents a BCD number and is defined in Table I Any
unused bits are held at a logical zero during a read and
ignored during a write An unused bit is any bit not neces-
sary to provide a full BCD number For example tens of
hours cannot legally exceed the number 2 thus only 2 bits
are necessary to define the tens of hours The other 2 bits in
the tens of hours digit are unused The unused bits are des-
ignated in Table I as dashes
The addressable portion of the counter is from milliseconds
to months The counter itself is a ripple counter The ripple
delay is less than 60 ms above 45V and 300 ms at 22V
RAM
56 bits of RAM are contained on-chip These can be used
for any necessary power down storage or as an alarm latch
for comparison to the real time counter The data in the
RAM can be compared to the real time counter on a digit
basis The only digits that are not compared are the unit ten
thousandths of seconds and tens of days of the week
(these are unused in the real time counter) If the two most
significant bits of any RAM digit are ones then this RAM
location will always compare The rule of thumb for an
‘‘a(chǎn)larm’’ interrupt is All nibbles of higher order than speci-
fied are set to C hex (always compare) All nibbles lower
than specified are set to ‘‘zero’’ As an example if an alarm
is to occur everyday at 1015 am configure the bits in RAM
as shown in Table II
The RAM is formatted the same as the real time counter 4
bits per digit 14 digits however there are no unused bits
The unused bits in the real time counter will compare only to
zeros in the RAM
An address map is shown in Table III
Interrupts and Comparator
There are two interrupt outputs The first is the INTERRUPT
OUTPUT (a true high signal) This output can be pro-
grammed to provide 8 different output signals They are
10 Hz once per second once per minute once per hour
once a day once a week once a month and when a RAM
real time counter comparison occurs To enable the output
a one is written into the interrupt control register at the bit
location corresponding to the desired output frequency (
Fig-
ure 1 ) Once one or more bits have been set in the interrupt
control register the corresponding counter’s rollover to its
reset state will clock the interrupt status register and cause
the interrupt output to go high To reset the interrupt and to
identify which frequency caused the interrupt the interrupt
status register is read Reading this register places the con-
tents of the status register on the data bus The interrupting
frequency will be identified by a one in the respective bit
position Removing the read will reset the interrupt
The second interrupt is the STANDBY INTERRUPT (open
drain output active low) This interrupt occurs when enabled
and when a RAMreal time counter comparison occurs The
STANDBY INTERRUPT is enabled by writing a one on the
D0 line at address 16H or disabled by writing a zero on the
D0 line This interrupt is not triggered by the edge of the
compare signal but rather by the level Thus if the compare
is enabled when the STANDBY INTERRUPT is enabled the
interrupt will turn on immediately
TABLE I Real Time Counter Format
Units
Max
Tens
Max
Counter Addressed
D0
D1
D2
D3
BCD
D4
D5
D6
D7
BCD
Code
Milliseconds
(00H)
0
D4
D5
D6
D7
9
Hundredths and Tenths Sec
(01H)
D0
D1
D2
D3
9
D4
D5
D6
D7
9
Seconds
(02H)
D0
D1
D2
D3
9
D4
D5
D6
5
Minutes
(03H)
D0
D1
D2
D3
9
D4
D5
D6
5
Hours
(04H)
D0
D1
D2
D3
9
D4
D5
2
Day of the Week
(05H)
D0
D1
D2
7
0
Day of the Month
(06H)
D0
D1
D2
D3
9
D4
D5
3
Month
(07H)
D0D1D2D3
9
D4
1
() indicates unused bits
3
相關PDF資料 |
PDF描述 |
|---|---|
| MM58274CVX | 0 TIMER(S), REAL TIME CLOCK, PQCC20 |
| MM908E621ACDWB/R2 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 |
| MM908E621ACDWB | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 |
| MM908E622ACDWB/R2 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 |
| MM908E624ACDWB/R | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MM58174 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Microprocessor-Compatible Real-Time Clock |
| MM58174A | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Microprocessor-Compatible Real-Time Clock |
| MM58174AN | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Microprocessor-Compatible Real-Time Clock |
| MM58201 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Multiplexed LCD Driver |
| MM58241 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:MM58241 High Voltage Display Driver |
發布緊急采購，3分鐘左右您將得到回復。